Wayne-Dalton 9100 Benutzerhandbuch
30
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
4. Now is a good time to remove vehicles
or items from garage to provide clear
access to end brackets.
or items from garage to provide clear
access to end brackets.
5. flip the ratchet pawl knob on both
end brackets to the upper position (see
illustration).
end brackets to the upper position (see
illustration).
6. Raise door 2”-3” and then lower
door. Repeat process until anti-drop
device resets (see disengaged system
illustration on previous page).
door. Repeat process until anti-drop
device resets (see disengaged system
illustration on previous page).
imPoRTaNT: bE PREPARED TO SUPPORT
THE TOTAL WEIGHT Of THE DOOR.
THE TOTAL WEIGHT Of THE DOOR.
7. Cautiously remove the vice clamps
from the vertical tracks. With assistance,
lower the door.
from the vertical tracks. With assistance,
lower the door.
8. Check for spring tension. Starting on
the right hand side, place a ratchet and
5/8” socket on the TorqueMaster
the right hand side, place a ratchet and
5/8” socket on the TorqueMaster
®
Plus
winding shaft (see illustration). Ensure
ratchet is set so that it will tighten
counter clockwise on the right hand side,
and clockwise on the left hand side (if
applicable). If tension is present, remove
the ratchet and check the left hand side
(if applicable). If spring(s) have tension,
proceed to balancing Door; if no spring
tension is present, contact a qualified
door systems technician to replace the
spring(s).
ratchet is set so that it will tighten
counter clockwise on the right hand side,
and clockwise on the left hand side (if
applicable). If tension is present, remove
the ratchet and check the left hand side
(if applicable). If spring(s) have tension,
proceed to balancing Door; if no spring
tension is present, contact a qualified
door systems technician to replace the
spring(s).
TO AVOID POSSIbLE INjURY, HAVE A
TRAINED DOOR SYSTEM TECHNICIAN
MAkE ADjUSTMENTS/REPAIRS TO
CAbLES, SPRING ASSEMbLIES AND
OTHER HARDWARE.
TRAINED DOOR SYSTEM TECHNICIAN
MAkE ADjUSTMENTS/REPAIRS TO
CAbLES, SPRING ASSEMbLIES AND
OTHER HARDWARE.
balaNciNg DooR
Lift door and check its balance. Adjust
spring(s), if door lifts by itself (hard to pull
down) or if door is difficult to lift (easy to
pull down). Anytime spring adjustments
are made, ratchet pawl knob must be in
the upper position (see illustration).
An unbalanced door such as this can
cause
Lift door and check its balance. Adjust
spring(s), if door lifts by itself (hard to pull
down) or if door is difficult to lift (easy to
pull down). Anytime spring adjustments
are made, ratchet pawl knob must be in
the upper position (see illustration).
An unbalanced door such as this can
cause
idrive
®
or TorqueMaster
®
Plus
operation problems. To adjust spring(s),
only add or remove a maximum of 3/10
of a turn (three teeth of ratchet wheel) at
a time. both sides need to be adjusted
only add or remove a maximum of 3/10
of a turn (three teeth of ratchet wheel) at
a time. both sides need to be adjusted
PLACE VICE CLAMPS
bELOW bOTTOM SECTION
ON bOTH VERTICAL TRACk
PAWL kNOb IN LOWER
POSITION
PAWL kNOb IN UPPER
POSITION
loweR PoSiTioN
uPPeR PoSiTioN
RATCHET
WITH 5/8”
SOCkET
END bRACkET
3” EXTENSION
Torquemaster
®
Plus Reset
instructions continued...
PAWL
waRNiNg