Hampton Direct H25-LP1 Propane Benutzerhandbuch
20
Hampton
®
H25-1 Direct Vent Freestanding Gas Stove
INSTALLATION
Note: The pipe seam should be
facing down.
Note: To make the installation more aes-
thetically pleasing, we recommend
framing out a square that the cap
can be mounted on.
framing out a square that the cap
can be mounted on.
3) Attach the 4" dia. fl ex liner to the vent ter-
minal ensuring that the fl ex overlaps the
collar of the vent terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal
and secure with 3 of the #8 x 1/2" screws
(stainless steel).
collar of the vent terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal
and secure with 3 of the #8 x 1/2" screws
(stainless steel).
4) Attach the adjustable pipe section to the
vent terminal using Mill-Pac and/or high
temperature silicone and attach with 3 of
the #8 x 1/2" screws (stainless steel).
temperature silicone and attach with 3 of
the #8 x 1/2" screws (stainless steel).
NOTE: For best results and optimum per-
formance with each approved vent-
ing system, it is highly recommended
to apply “Mill-Pac” sealant (supplied)
to every inner pipe connection. Fail-
ure to do so may result in drafting
or performance issues not covered
under warranty. Silicone (red RTV)
is optional.
ing system, it is highly recommended
to apply “Mill-Pac” sealant (supplied)
to every inner pipe connection. Fail-
ure to do so may result in drafting
or performance issues not covered
under warranty. Silicone (red RTV)
is optional.
Note: If installing ter-
mination on a
siding covered
wall, a vinyl sid-
ing standoff or
f u r r i n g s t r i p s
must be used to
ensure that the
termination is not
recessed into the
siding. For vinyl siding standoff
installation refer to the Dura-Vent
Termination instructions.
siding covered
wall, a vinyl sid-
ing standoff or
f u r r i n g s t r i p s
must be used to
ensure that the
termination is not
recessed into the
siding. For vinyl siding standoff
installation refer to the Dura-Vent
Termination instructions.
5) Slide the partially connected pipe and
vent terminal assembly through the wall
thimbles (from the exterior into the interior)
and secure the cap to the exterior wall with
4 of the supplied screws (#8 x 1-1/2" drill
point, stainless steel). Note: pilot holes will
need to be drilled through the wall thimble
on all 4 corners.
thimbles (from the exterior into the interior)
and secure the cap to the exterior wall with
4 of the supplied screws (#8 x 1-1/2" drill
point, stainless steel). Note: pilot holes will
need to be drilled through the wall thimble
on all 4 corners.
Note: The four screws provided for the
vent cap should be replaced with
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
appropriate fasteners for stucco,
brick, concrete, or other types of
sidings.
6) A bead of non-hardening mastic should
be run around both the termination and
vinyl siding standoff to prevent water from
entering and to make a tight seal between
the cap and the standoff.
vinyl siding standoff to prevent water from
entering and to make a tight seal between
the cap and the standoff.
7) Stretch the 4" dia. fl ex liner out fully and get
a trial fi t of the liner onto the 4" dia. starter
collar.
collar.
8) Cut the 4" dia. fl ex liner to the desired
size.
Hint: leave an extra 12" to 16" of length,
this will make the fi nal assembly easier to
work with.
this will make the fi nal assembly easier to
work with.
9) Secure the 4" dia. fl ex liner to the 4" adapter
with Mill-Pac and 3 of the #8 x 1/2" screws
(stainless steel).
(stainless steel).
10) Slide the decorative Thimble Cover over the
pipe sections and secure with 4 screws (#8
x 1-1/2" drill point, black) to the wall.
x 1-1/2" drill point, black) to the wall.
11) Slide the 90
o
elbow (crimp end up), the 45
o
elbow and the 4 ft. pipe section (crimp end
up) over the 4" dia. fl ex liner.
up) over the 4" dia. fl ex liner.
12) Install the spring spacers onto the pipe sec-
tions.
13) Secure the 4" dia. fl ex liner with adapter
onto the stove collar. Put a bead of Mill-Pac
around the appliance adapter and secure
with 3 screws (#8 x 1/2, stainless steel).
around the appliance adapter and secure
with 3 screws (#8 x 1/2, stainless steel).
14) Attach the 45
o
elbow onto the starter collar by
sealing with Mill-Pac and/or high temperature
silicone and securing with 3 of the #8 x 1/2"
(black) screws.
silicone and securing with 3 of the #8 x 1/2"
(black) screws.
15) Attach the pipe section to the 45
o
elbow by
sealing with Mill-Pac and/or high temperature
silicone and securing with 3 of the #8 x 1/2"
screws (black). Pipe seams should be facing
the wall.
silicone and securing with 3 of the #8 x 1/2"
screws (black). Pipe seams should be facing
the wall.
16) Attach the 90
o
elbow onto the pipe section by
sealing with Mill-Pac and/or high temperature
silicone and securing with 3 of the #8 x 1/2"
screws (black).
silicone and securing with 3 of the #8 x 1/2"
screws (black).
17) Slide the adjustable pipe section onto the 90
o
elbow. Slide the trim collar over the adjust-
able pipe sections to cover the joint of the
telescopic section.) The fl ex may have to be
compressed back in order for the adjustable
pipe to properly mate to the elbow. Seal with
Mill-Pac and/or high temperature silicone and
secure with 3 of the #8 x 1/2" screws (black).
Pipe seams facing down.
able pipe sections to cover the joint of the
telescopic section.) The fl ex may have to be
compressed back in order for the adjustable
pipe to properly mate to the elbow. Seal with
Mill-Pac and/or high temperature silicone and
secure with 3 of the #8 x 1/2" screws (black).
Pipe seams facing down.
18) Install the trim collar over the starter collar
and secure with a #8 x 1/2" screw (black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
Stove Brite High Temperature Metallic Black
Stove Paint.