Hampton Direct H25-LP1 Propane Benutzerhandbuch
Hampton
®
H25-1 Direct Vent Freestanding Gas Stove
21
Pipe Length (max. 18")
Part (6-5/8" Dia)
(4" Dia.)
Decorative
Wall Trim
Part #640-545/P
Horizontal
Terminal
Part# 640-530/P
Terminal
Part# 640-530/P
Wall Thimble
Part # 946-202
(required for
combustible walls)
Vinyl Siding
Standoff (Optional)
Part #946-205
Standoff (Optional)
Part #946-205
Adapter
Part #946-219/P
(required)
INSTALLATION
RESIDENTIAL AND MANUFACTURED HOMES / MOBILE HOMES
MINIMUM HORIZONTAL TERMINATION INSTALLATIONS
You will require the following components with your new Hampton
®
Rear Vent Direct Vent Free-
standing Gas Stove. Please review your product to make sure you have everything you need. In
the event that you are missing any part, contact your dealer. Decorative brass
or chrome trim kits are available from Simpson Dura-Vent for their
wall thimbles, as well as a square wall thimble cover.
the event that you are missing any part, contact your dealer. Decorative brass
or chrome trim kits are available from Simpson Dura-Vent for their
wall thimbles, as well as a square wall thimble cover.
Planning Your venting Installation
See the "Exterior Vent Terminatal Locations"
section for requirements. The H25 is approved
for a minimum horizontal termination with the
FPI Riser Vent Kit. See the diagram for minimum
and maximum pipe lengths.
section for requirements. The H25 is approved
for a minimum horizontal termination with the
FPI Riser Vent Kit. See the diagram for minimum
and maximum pipe lengths.
When planning your installation, it will be nec-
essary to select the proper length of vent pipe
for your particular requirements. Determine the
minimum clearance to combustibles from the
rear of the unit to the wall. It is also important to
note the wall thickness. Before cutting the vent
hole through the wall ensure that ALL vent and
termination clearances (see the "Exterior Vent
Terminal locations" section) will be met.
essary to select the proper length of vent pipe
for your particular requirements. Determine the
minimum clearance to combustibles from the
rear of the unit to the wall. It is also important to
note the wall thickness. Before cutting the vent
hole through the wall ensure that ALL vent and
termination clearances (see the "Exterior Vent
Terminal locations" section) will be met.
*If this is an outside corner, the minimum distance
between the vent and the outside corner is 6"
(15cm). See "F" on the diagram in the "Exterior
Vent Terminal Locations" section.
between the vent and the outside corner is 6"
(15cm). See "F" on the diagram in the "Exterior
Vent Terminal Locations" section.
NOTE: Ensure compliance with the outside
vent terminal location before cutting hole as
both dimensions must be met.
vent terminal location before cutting hole as
both dimensions must be met.
Note: These are the minimum pieces re-
quired. Other parts may be required
for your particular installation.
for your particular installation.
Minimum components for a Horizontal Installation:
640-944
640-944
Horizontal Termination Kit which includes:
1
6-5/8" Dia. x 18" Black Pipe
1
4" Dia. x 18" Aluminum Vent
1 946-202
Wall Penetration Heat Shield (Wall Thimble) (2 pcs)
1
640-530/P
Riser
Vent
Terminal
1
640-545/P
Decorative
Wall
Trim
(Black)
1
948-128
Tube
Mill-Pac
Screws
946-219/P 1 Adapter
Optional Components:
946-204
946-204
45
o
Elbow - 6-5/8" Black pipe
and 4" Aluminum Vent
946-205
Vinyl Siding Shield for Riser Vent
Terminal
946-208/P Vent
Guard
940
Square Wall Thimble Cover*
981
Snorkel
Termination
(36")*
982
Snorkel
Termination
(14")*
942
Wall
Penetration
Heat
Shield*
* Simpson Dura-Vent components