Haier HSU-24HEK03/R2 Benutzerhandbuch
2
Outdoor Unit
Loading of the battery
1
2
3
4
Parts and Functions
Indoor Unit
OUTLET
INLET
CONNECTING PIPING AND ELECTRICAL WIRING
DRAIN HOSE
Remote controller
Remove the battery cover;
Load the batteries as illustrated.
2 R-03 batteries, resetting key
(cylinder);
Be sure that the loading
is in line with th
e" + "/"-";
Load the battery,then put on the cover again.
Clock set
Press CLOCK button, "AM" or "PM" flashes.
Press or to set correct time. Each press
change quickly. After time setting is confirmed,press SET,
"AM "and "PM" stop flashing,while clock starts working.
or decrease 1min. If the button is kept pressed,time will
will increase
The distance between the signal transmission head and the rece-
iver hole should be within 7m without any obstacle as well.
iver hole should be within 7m without any obstacle as well.
When electronic-sta rted type fluorescent lamp or change- over
wireless telephone is installed in the
ver is apt to be disturbed in receiving the signals,
so the distance to the indoor unit should be shorter.
type fluorescent lamp or
room, the recei
room, the recei
Note:
Full display or unclear display during operation indicates the
ries have been used up.Please change batteries.
If the remote controller can't run normally during operation, please
reload several minutes later.
batte
remove the batteries and
Please be subject to the actual produce purchased the
above picture is just from your reference
above picture is just from your reference
Please be subject to the actual produce purchased the
above picture is just from your reference
above picture is just from your reference
Air Purifying Filter
(inside)
Inlet
1
Inlet grille
2
Outlet
3
(adjust left and right air flow)
Vertical blade
4
Display board
Horizontal flap
(adjust up and down air flow.
Don't adjust it manually)
Emergency Switch
6
7
8
5
1
2
3
4
5
6
7
8
11
10
8
9
13
14
15
16
15
16
12
17
ON/OFF
FAN
MODE
SWING
TIMER
CLOCK
SET
SLEEP
LOCK
RESET
18
4
22
19
23
1
6
5
2
21
3
24
POWER/SOFT
LIGHT
20
LOCK
RESET
TIMER
CLOCK
SET
SLEEP
POWER/SOFT
LIGHT
7
9. LOCK display
10. SWING display
11. Mode display
10. SWING display
11. Mode display
LO
MED
HI
AUTO
POWER
SOFT
BLANK
12. TEMP display
13. SIGNAL SENDING
14. TIMER OFF display
15. TIMER ON display
16. CLOCK display
17. SLEEP display
18. POWER ON/OFF button
19. SWING button
20. HOUR / POWER/SOFT button
Used to set clock and timer setting.
Press this button at any time except
for setting the remote control time
and setting time
13. SIGNAL SENDING
14. TIMER OFF display
15. TIMER ON display
16. CLOCK display
17. SLEEP display
18. POWER ON/OFF button
19. SWING button
20. HOUR / POWER/SOFT button
Used to set clock and timer setting.
Press this button at any time except
for setting the remote control time
and setting time
display changes
as follows:
21. TIMER button
Used to set correct time.
22. HOUR button
23. SLEEP button
24. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this
button to reset the remote
controller normal.
Used to set correct time.
22. HOUR button
23. SLEEP button
24. RESET button
When the remote controller
appears abnormal, use a sharp
pointed article to press this
button to reset the remote
controller normal.
Operation mode
AUTO
FAN
COOL
DRY
Remote controller
HEAT
1. LOCK button
Used to lock buttons and
LCD display.
2. SET / LIGHT button
3. CLOCK button
4. MODE button
5. TEMP.SETTING button
6. FAN button
7. HEALTH display
8. FAN SPEED display
Used to lock buttons and
LCD display.
2. SET / LIGHT button
3. CLOCK button
4. MODE button
5. TEMP.SETTING button
6. FAN button
7. HEALTH display
8. FAN SPEED display
4
Hint:
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.
Remove the batteries in case won't be in use for a long period. If
there is any display after taking-out, just press reset key.