Numark Industries CDN 36 Benutzerhandbuch
CDN 36
REAR PANEL FEATURES
26. Control Cable Connector- Plug in the 8-pin cable included in here to connect the remote control and main CD
unit together
27. IEC Power Plug Connector - Plug your supplied power cord in here.
28. Voltage Selector - Set this switch to the voltage for your location.
29. RCA Audio Connectors - Connect your CD player to your mixer from this line level output.
30. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In
28. Voltage Selector - Set this switch to the voltage for your location.
29. RCA Audio Connectors - Connect your CD player to your mixer from this line level output.
30. Digital Output - The format is type 2, form 1, also known as S/PDIF (Sony/Phillips Digital Interface Format). In
order to use the digital output you should not use variable pitch slider and the pitch bend buttons. If you adjust
the pitch, other devices may not read the digital output properly because the sampling rate changes
31. Remote Start Connector – Use this connector to plug into your fader start compatible mixer or remote switch.
This function is always active. To use this connector for fader start, connect the supplied fader start cable to a
fader start compatible mixer. Every time you move the crossfader on the mixer over to the side that the unit is
on, it will automatically start playing. When you move the fader away from that side, the unit will stop. Moving
the fader back to the unit side will start play again.
There are two potential modes associated with the switch PLAY-CUE and PLAY/PAUSE. The factory setting is
PLAY-CUE mode. This means that when the unit is remotely stopped it will go back to the cue point automatically.
To change modes hold down the time button for 3 seconds and the display will flash the play “ " and pause “
the fader back to the unit side will start play again.
There are two potential modes associated with the switch PLAY-CUE and PLAY/PAUSE. The factory setting is
PLAY-CUE mode. This means that when the unit is remotely stopped it will go back to the cue point automatically.
To change modes hold down the time button for 3 seconds and the display will flash the play “ " and pause “
” icons. In PLAY/PAUSE mode, moving the crossfader away from the unit side pauses right where it is, and
resumes when the fader is brought back to the unit. To change modes back to PLAY-CUE hold down the time
button for 3 seconds and the display will flash the play “ " and cue “
resumes when the fader is brought back to the unit. To change modes back to PLAY-CUE hold down the time
button for 3 seconds and the display will flash the play “ " and cue “
” icons in the display.
32. Remote Assignment Switch - Set this switch in the position for the method of remote start you will be using.
Foot switches are often used for creative mixing techniques and can be found in most music shops. Connector
plugs are often ¼” and an adapter to 1/8” will be needed for connection. There are also two types of footswitches
plugs are often ¼” and an adapter to 1/8” will be needed for connection. There are also two types of footswitches
that will work with this connector. The first is a typical, on/off pushbutton switch and are generally used for
switching channels on guitar amps. The second switch is a momentary footswitch and is usually used for
keyboard sustain pedals. If you are unsure of the style of switch you have, try each position until it works as
keyboard sustain pedals. If you are unsure of the style of switch you have, try each position until it works as
desired.
•
ON-OFF – for use with an ON-OFF switch.
•
MOMENTARY – for use with a momentary style of switch.
•
MIXER – for use with a fader start compatible DJ mixer
- The Leader in DJ Technology
©2002 Numark Industries
- 8 -
http://www.numark.com