JVC KDC-BT92SD Benutzerhandbuch

P.CONT

ANT.CONT

 MUTE

REMOTE CONT

STEERING WHEEL

REMOTE INPUT

1 

2 

3 

4 

5 

6 

7 

8 

1 

2 

3 

4 

5 

6 

7 

8 

L

R

L

R

Yellow (Battery wire)

Red (Ignition wire)

FM/AM antenna input (JASO)

Antenna Cord 

Wiring harness 
(Accessory 1)

If no connections are made, do not 
let the wire come out from the tab.

Blue/White (Power control/
Antenna control wire)

Brown (Mute control wire)

Connect either to the power control terminal when 
using the optional power amplifier, or to the antenna 
control terminal in the vehicle. (Max. 300mA, 12V)

Red (A–7 Pin)
Yellow (A–4 Pin)

Connector A

Connector B

⁄

 See next page

Fuse (10A)

Front output

Rear output

Sub Woofer output

To connect the Kenwood navigation system, consult 

your navigation manual.

Light Blue/Yellow (Steering 

remote control wire)

USB connector (0.8m)

To USB device

⁄

 Do not remove the 

cap when you do not 
use the USB cable. The 
connector will cause 
the unit to malfunction 
if it gets in touch with 
any metallic part of the 
vehicle.

Microphone 
(Accessory 3)

Microphone input 

AUX input (Stereo) 
Use the mini-plug which is stereo type 
and does not have any resistance.

To use the steering wheel remote control feature, you 
need to an exclusive remote adapter (not supplied) 
matches your car is required.

|

KDC-BT92SD

English

   

|

   

1

..........1

 

2

..........2

3

3 m

 ..........1

To prevent short circuits, remove the key from the 

ignition and disconnect the - terminal of the 

battery.

Make the proper input and output wire 

connections for each unit.

Connect the wire on the wiring harness.

Take Connector B on the wiring harness and 

connect it to the speaker connector in your vehicle.

Take Connector A on the wiring harness and 

connect it to the external power connector on your 

vehicle.

Connect the wiring harness connector to the unit.

Install the unit in your car.

Reconnect the - terminal of the battery.

Press the reset button.

¤

•  Mounting and wiring this product requires skills and

experience. For safety’s sake, leave the mounting and wiring 
work to professionals.

•  Make sure to ground the unit to a negative 12V DC power

supply.

•  Do not install the unit in a spot exposed to direct sunlight

or excessive heat or humidity. Also avoid places with too 
much dust or the possibility of water splashing.

•  Do not use your own screws. Use only the screws provided.

If you use the wrong screws, you could damage the unit.

•  If the power is not turned ON (“Protect” is displayed), the

speaker wire may have a short-circuit or touched the 
chassis of the vehicle and the protection function may 
have been activated. Therefore, the speaker wire should be 
checked.

•  Make sure that all wire connections are securely made by

inserting jacks until they lock completely.

•  If your vehicle’s ignition does not have an ACC position, or

if the ignition wire is connected to a power source with 
constant voltage such as a battery wire, the power will not 
be linked with the ignition (i.e., it will not turn on and off 
along with the ignition). If you want to link the unit’s power 

with the ignition, connect the ignition wire to a power 
source that can be turned on and off with the ignition key.

•  Use a commercially available conversion connector if the

connector does not fit in the vehicle connector.

•  Insulate unconnected wires with vinyl tape or other similar

material. To prevent a short circuit, do not remove the caps 
on the ends of the unconnected wires or the terminals.

•  If the console has a lid, make sure to install the unit so that

the faceplate will not hit the lid when closing and opening.

•  If the fuse blows, first make sure the wires aren’t touching

to cause a short circuit, then replace the old fuse with one 
with the same rating.

•  Connect the speaker wires correctly to the terminals to

which they correspond. The unit may be damaged or fail to 
work if you share the - wires or ground them to any metal 
part in the car. 

•  After the unit is installed, check whether the brake lamps,

blinkers, wipers, etc. on the car are working properly.

•  Mount the unit so that the mounting angle is 30° or less.
•  Reception may drop if there are metal objects near the

Bluetooth antenna. 

Bluetooth antenna unit  

To assure good reception, note the following:
•  Communicate with the cell-phone within the line-

of-sight distance of 10 m (30 ft). The communication

range becomes shorter depending on the 

surrounding environment. The communication 

range also becomes shorter when there is an 

obstacle between this unit and the cell-phone. The 

above maximum communication range (10 m) is

not always assured. 

•  A broadcast station or walkie-talkie located nearby

can interfere with communication due to too strong 

signal.