Korg PA50 Benutzerhandbuch
212
Effects
Mono – Mono Chain
062: P4Eq-TapDly
(Parametric 4-Band EQ – Multitap Delay)
This effect combines a mono-type four-band parametric
equalizer and a multitap delay.
equalizer and a multitap delay.
063: Cmp-AutoWah
(Compressor – Wah/Auto Wah)
This effect combines a mono-type compressor and a wah.
You can change the order of the connection.
You can change the order of the connection.
a
[E] Trim
Sets the parametric EQ input level
Sets the parametric EQ input level
0...100
b
[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1
Sets the center frequency of Band 1
20...1.00kHz
Q
Sets the bandwidth of Band 1
Sets the bandwidth of Band 1
0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 1
Sets the gain of Band 1
–18...+18dB
c
[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2
Sets the center frequency of Band 2
50...5.00kHz
Q
Sets the bandwidth of Band 2
Sets the bandwidth of Band 2
0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 2
Sets the gain of Band 2
–18...+18dB
d
[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3
Sets the center frequency for Band 3
300...10.00kHz
Q
Sets the bandwidth of Band 3
Sets the bandwidth of Band 3
0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 3
Sets the gain of Band 3
–18...+18dB
e
[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4
Sets the center frequency for Band 4
500...20.00kHz
Q
Sets the bandwidth of Band 4
Sets the bandwidth of Band 4
0.5...10.0
☞
Fx:006
Gain [dB]
Sets the gain of Band 4
Sets the gain of Band 4
–18...+18dB
f
[D] Tap1 Time [msec]
Sets the Tap1 delay time
Sets the Tap1 delay time
0...680msec
Tap1 Level
Sets the Tap1 output level
Sets the Tap1 output level
0...100
☞
Fx:045
g
[D] Tap2 Time [msec]
Sets the Tap2 delay time
Sets the Tap2 delay time
0...680msec
Feedback
Sets the Tap2 feedback amount
Sets the Tap2 feedback amount
–100...+100
h
[D] Mt.Delay Wet/DryDry, 2:98...98:2, Wet
Sets the multitap delay effect balance
Sets the multitap delay effect balance
High Damp [%]
Sets the damping amount in the high range
Sets the damping amount in the high range
0...100%
☞
Fx:043
i
Wet/DryDry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on
page 175
Table , “Sets the balance between the effect and dry sounds,” on
page 175
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Trim
+
Parametric 4Band EQ
Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly Wet / Dry
a
[C] Sensitivity
Sets the sensitivity
Sets the sensitivity
1...100
☞
Fx:002
b
1...100
☞
Fx:002
Output Level
Sets the compressor output level
Sets the compressor output level
0...100
☞
Fx:002
c
0...100
d
[C] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176
Table , “Sets the gain of Low EQ,” on page 176
–15...+15dB
Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176
Table , “Sets the gain of High EQ,” on page 176
–15...+15dB
e
[W] Frequency Bottom
Sets the lower limit of the wah center frequency
Sets the lower limit of the wah center frequency
0...100
☞
Fx:009
Frequency Top
Sets the upper limit of the wah center frequency
Sets the upper limit of the wah center frequency
0...100
☞
Fx:009
f
[W] Sweep Mode
Auto, D-mod, LFO
Selects the control from auto-wah, modulation source, and LFO
☞
Fx:009,
Src
Off...Tempo
Selects the modulation source for the wah when Sweep Mode=D-mod
g
[W] LFO Frequency [Hz]
Sets the LFO speed
Sets the LFO speed
0.02...20.00Hz
h
[W] Resonance
Sets the resonance amount
Sets the resonance amount
0...100
Low Pass Filter
Switches the wah low pass filter on and off
Switches the wah low pass filter on and off
Off, On
i
Routing
CMP
→ WAH, WAH
→
CMP
Switches the order of the compressor and wah connection
j
Wet/Dry
Dry, 1:99...99:1, Wet
Src
Off...Tempo
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Compressor
Routing
Wah/Auto Wah
Wah
D
-mod
Envelope
Sweep Mode
D-mod
Auto
LFO
LFO
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control