Korg PA50 Benutzerhandbuch

Mono – Mono Chain

This effect combines a mono-type compressor and a four-
band parametric equalizer. You can change the order of the
effect connection.

This effect combines a mono-type compressor and a chorus/
flanger. You can change the order of the effect connection.

h: Output Mode, i: Routing
When  Wet Invert is selected, the right channel phase of
the chorus/flanger effect sound is inverted. This creates
pseudo-stereo effects and adds spread.
However, if a mono-input type effect is connected after
this effect, the left and right sounds may cancel each
other, eliminating the chorus/flanger effects.
When “Routing” is set to FLNG

→CMP, “Output Mode”

will be set to Normal.

a

[C] Sensitivity
Sets the sensitivity

1...100

☞

 Fx:002

b

[C] Attack
Table , “Sets the attack level,” on page 176

1...100

☞

 Fx:002

Output Level
Sets the compressor output level

0...100

☞

 Fx:002

c

[E] Trim
Sets the parametric EQ input level

0...100

d

[E] Band1 Cutoff [Hz]
Sets the center frequency of Band 1

20...1.00kHz

Q
Sets the bandwidth of Band 1

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 1

–18...+18dB

e

[E] Band2 Cutoff [Hz]
Sets the center frequency of Band 2

50...5.00kHz

Q
Sets the bandwidth of Band 2

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 2

–18...+18dB

f

[E] Band3 Cutoff [Hz]
Sets the center frequency for Band 3

300...10.00kHz

Q
Sets the bandwidth of Band 3

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 3

–18...+18dB

g

[E] Band4 Cutoff [Hz]
Sets the center frequency for Band 4

500...20.00kHz

Q
Sets the bandwidth of Band 4

0.5...10.0

☞

 Fx:006

Gain [dB]
Sets the gain of Band 4

–18...+18dB

h

Routing

CMP 

→ PEQ, PEQ → CMP

Switches the order of the compressor and parametric EQ connection

i

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175

–100...+100

+

a

[C] Sensitivity
Sets the sensitivity

1...100

☞

 Fx:002

b

[C] Attack
Table , “Sets the attack level,” on page 176

1...100

☞

 Fx:002

Output Level
Sets the compressor output level

0...100

☞

 Fx:002

c

[C] EQ Trim
Table , “Sets the EQ input level,” on page 176

0...100

d

[C] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176

–15...+15dB

Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176

–15...+15dB

e

[F] Delay Time [msec]
Sets the delay time

0.0...50.0msec

f

[F] LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

LFO Waveform
Selects LFO Waveform

Triangle, Sine

g

[F] Depth
Sets the depth of LFO modulation

0...100

Feedback
Sets the feedback amount

–100...+100

☞

 Fx:020

h

[F] Cho/Flng Wet/Dry

–Wet...–2:98, Dry, 2:98...Wet

Sets the effect balance of the chorus/flanger

☞

 Fx:010, 020

Output Mode

Normal, Wet Invert

Selects the output mode for the chorus/flanger

☞

i

Routing

CMP 

→ FLNG, FLNG → CMP

Switches the order of the compressor and chorus/flanger connection 

☞

j

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175

–100...+100

+