Korg PA50 Benutzerhandbuch
222
Effects
Mono – Mono Chain
083: Wah-AmpSim
(Wah/Auto Wah – Amp Simulation)
This effect combines a mono-type wah and an amp simula-
tion. You can change the order of the effect connection.
tion. You can change the order of the effect connection.
084: Decim-Amp S
(Decimator – Amp Simulation)
This effect combines a mono-type decimator and an amp
simulation. You can change the order of the effect connec-
tion.
simulation. You can change the order of the effect connec-
tion.
085: Decim-Cmp
(Decimator – Compressor)
This effect combines a mono-type decimator and a compres-
sor. You can change the order of the effect connection.
sor. You can change the order of the effect connection.
a
[W] Frequency Bottom
Sets the lower limit of the wah center frequency
Sets the lower limit of the wah center frequency
0...100
☞
Fx:009
Frequency Top
Sets the upper limit of the wah center frequency
Sets the upper limit of the wah center frequency
0...100
☞
Fx:009
b
[W] Sweep Mode
Auto, D-mod, LFO
Selects the control from auto-wah, modulation source, and LFO
☞
Fx:009,
Src
Off...Tempo
Selects the modulation source for the wah when Sweep Mode=D-mod
c
[W] LFO Frequency [Hz]
Sets the LFO speed
Sets the LFO speed
0.02...20.00Hz
d
[W] Resonance
Sets the resonance amount
Sets the resonance amount
0...100
Low Pass Filter
Switches the wah low pass filter on and off
Switches the wah low pass filter on and off
Off, On
e
[A] Amplifier Type
Selects the type of guitar amplifier
Selects the type of guitar amplifier
SS, EL84, 6L6
f
Routing
WAH
→ AMP, AMP → WAH
Switches the order of the wah and amp simulation connection
g
Wet/Dry
Dry, 1:99...99:1, Wet
Src
Off...Tempo
–100...+100
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Routing
Amp Simulation
Amp Simulation Filter
Wah/Auto Wah
Wah
D
-mod
Envelope
Sweep Mode
D-mod
Auto
LFO
LFO
a
[D] Pre LPFOff, On
Turn the harmonic noise caused by lowered sampling on and off
Turn the harmonic noise caused by lowered sampling on and off
☞
Fx:014
High Damp [%]
Sets the ratio of high-range damping
Sets the ratio of high-range damping
0...100%
b
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
Sets the sampling frequency
1.00k...48.00kH
z
Resolution
Sets the data bit length
Sets the data bit length
4...24
☞
Fx:014
c
[D] Output Level
Sets the decimator output level
Sets the decimator output level
0...100
☞
Fx:014
d
[A] Amplifier Type
Selects the type of guitar amplifier
Selects the type of guitar amplifier
SS, EL84, 6L6
e
RoutingDECI
→AMP, AMP→DECI
Switches the order of the wah and amp simulation connection
f
Wet/DryDry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on
page 175
Table , “Sets the balance between the effect and dry sounds,” on
page 175
–100...+100
a
[D] Pre LPF
Off, On
Turn the harmonic noise caused by lowered sampling on and off
☞
Fx:014
High Damp [%]
Sets the ratio of high-range damping
Sets the ratio of high-range damping
0...100%
b
[D] Sampling Freq [Hz] (Sampling Frequency)
Sets the sampling frequency
Sets the sampling frequency
1.00k...48.00kHz
Resolution
Sets the data bit length
Sets the data bit length
4...24
☞
Fx:014
c
[D] Output Level
Sets the decimator output level
Sets the decimator output level
0...100
☞
Fx:014
d
[C] Sensitivity
Sets the sensitivity
Sets the sensitivity
1...100
☞
Fx:002
e
1...100
☞
Fx:002
Output Level
Sets the compressor output level
Sets the compressor output level
0...100
☞
Fx:002
f
Routing
DECI
→CMP, CMP→DECI
Switches the order of the decimator and compressor connection
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
+
Decimator
Routing
Pre LPF
High Damp
Output Level
Decimator
Resolution
Compressor
Comp
Output Level
Envelope - Control