Korg PA50 Benutzerhandbuch

Mono – Mono Chain

This effect combines a mono-type phaser and a chorus/
flanger.

This effect combines a mono-type reverb and a gate.

f: Envelope Select, f: Src, g: Input Reverb Mix, g: Threshold
The “Envelope Select” parameter enables you to select
whether turning the gate on and off is triggered by the
input signal level or controlled directly by the modulation
source. You can select from Off to Gate2+Dmpr for the Src
parameter to specify the modulation source. 
When “Envelope Select” is set to Input, the gate is con-
trolled by the level of signals that are the combination of
the dry sound and the reverb sound. When the signal level
exceeds the threshold, the gate opens and the reverb
sound is output.
Normally, set “Input Reverb Mix” to Dry (the gate is con-
trolled only by the dry sound). If you wish to extend the
gate time, set the “Input Reverb Mix” value higher and
adjust the “Threshold” value.

a

[P] LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

LFO Waveform
Selects LFO Waveform

Triangle, Sine

b

[P] Manual
Sets the frequency to which the effect is applied

0...100

Depth
Sets the depth of LFO modulation

0...100

Resonance
Sets the resonance amount

–100...+100

☞

 Fx:023

c

[P] Phaser Wet/Dry

–Wet...–2:98, Dry, 2:98...Wet

Sets the phaser effect balance

☞

 Fx:010, 023

d

[F] LFO Frequency [Hz]
Sets the LFO speed

0.02...20.00Hz

LFO Waveform
Selects LFO Waveform

Triangle, Sine

e

[F] Delay Time [msec]
Sets the delay time

0.0...50.0msec

Depth
Sets the depth of LFO modulation

0...100

Feedback
Sets the feedback amount

–100...+100

☞

 Fx:020

f

[F] EQ Trim
Table , “Sets the EQ input level,” on page 176

0...100

g

[F] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176

–15...+15dB

Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176

–15...+15dB

h

[F] Cho/Flng Wet/Dry

–Wet...–2:98, Dry, 2:98...Wet

Sets the effect balance of the chorus/flanger

☞

 Fx:010, 020

Output Mode

Normal, Wet Invert

Selects the output mode for the chorus/flanger

☞

 Fx:060

i

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175

–100...+100

+

a

[R] Reverb Time [sec]
Sets the reverberation time

0.1...10.0sec

High Damp [%]
Sets the damping amount in the high range

0...100%

b

[R] Pre Delay [msec]

0...200msec

Sets the delay time of the reverb sound and gate control signal

c

[R] EQ Trim
Table , “Sets the EQ input level,” on page 176

0...100

d

[R] Pre LEQ Gain [dB]
Table , “Sets the gain of Low EQ,” on page 176

–15...+15dB

Pre HEQ Gain [dB]
Table , “Sets the gain of High EQ,” on page 176

–15...+15dB

e

[R] Reverb Balance

Dry, 1:99...99:1, Wet

Sets the reverb effect balance

f

[G] Envelope Select

D-mod, Input

Switches between modulation source control and input signal control 

☞

Src

Off...Gate2+Dmpr

Selects the modulation source that controls the gate when Envelope Select 
is set to D-mod

☞

g

[G] Input Reverb Mix

Dry, 1:99...99:1, Wet

Sets the balance between the dry and reverb sounds of the gate control sig-
nal.

☞

Threshold
Sets the gate threshold level

0...100

☞

h

[G] Polarity

+, –

Switches between non-invert and invert of the gate on/off state

☞

 Fx:005

i

[G] Attack
Sets the attack time

1...100

☞

 Fx:005

Release
Sets the release time

1...100

☞

 Fx:005

j

Wet/Dry

Dry, 1:99...99:1, Wet

Src

Off...Tempo

Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175

–100...+100

+