Sears 172.104 Benutzerhandbuch

OPERATION cont.

Do not hold the chuck body with one hand and use the power of the

drill / driver to tighten the chuck jaws on the accessory bit. The chuck body could slip in

your hand, or your hand could slip and come in contact with the rotating accessory bit.

This could cause an accident resulting in serious personal injury.

WARNING:

KEYLESS CHUCK (Fig. 7)

The drill/driver has a keyless chuck which allows you to hand tighten or loosen accessory bits

without the use of a chuck key.
1. Grasp and hold the rear chuck collar with one hand (see Fig. 7).

2. Rotate the front of the chuck with your other hand, clockwise (as viewed from the front

of the chuck), to CLOSE the chuck jaws and tighten (”GRIP”) the accessory bit in the jaws.

3. Rotate the front of the chuck

counterclockwise to OPEN the chuck jaws to loosen

(”RELEASE”) the accessory bit from the chuck jaws (see Fig. 7a).

Fig. 7

Companio

9.6 V

NOTE: ON THE VERY FRONT OF THE CHUCK there are “HANDS” that point the

direction to rotate the front of the chuck to “GRIP” or “RELEASE” the accessory

bits.

OPEN “RELEASE”

CLOSE “GRIP”

BUBBLE LEVELS (Fig. 8 an 8a)

In order to insure a perfect

right angle when drilling/driving

into a workpiece, you can use

the built-in bubble level on the

back of the drill / driver

(see Fig. 8). The bubble level

is designed to work when

drilling / driving in either a

horizontal or vertical position.

Line the air bubble up in the

appropriate circle, and the

drill/driver is in a perpendicular

angle to the workpiece. This

will insure that you drill/drive

straight into the workpiece.

Fig. 8

Align Bubble Level on Top

for Horizontal drilling

Fig. 8a

Align Bubble Level

on Back for Vertical drilling

Fig. 7a

10-4-07 Drill
10300-10400

OPERATION cont.

1. For normal drilling in wood, metal and plastics, turn and set the collar to the drilling

position symbol
2. For screw driving, turn and set the collar to the desired setting 1 through 15. If you are

not sure of the appropriate setting using the guidelines in the chart (Fig. 9b),

proceed as follows;
• Set the collar to the lowest setting, “1”
• Drive and tighten the first screw
• If the clutch ratchets before the screw is tightened, increase the torque setting and

continue to tighten the screw.

• Repeat this process until you reach a torque setting that drives and tightens the screw

without the clutch ratcheting.
• Use that torque setting to drive and tighten the remaining screws.

1 – 3 For driving small screws (least torque)
4 – 6 For driving screws into soft material
7 – 9 For driving screws into soft and hard materials
10 – 12 For driving screws in hard woods
13 – 15 For driving larger screws

For normal to heavy twist drilling into all building materials (most torque)

15 PLUS 1 ADJUSTABLE TORQUE CLUTCH (Fig. 9, 9a and 9b)

This drill / driver is equipped with an adjustable clutch that has 16 different torque settings.

These torque settings allow you to efficiently perform various drilling and screw driving

applications. To adjust the clutch, hold the handle of the drill /driver with one hand and with

the other hand turn the clutch collar to the left or right (see Fig. 9), and line the desired setting

(number or symbol) up to the embossed arrow on the top of the drill/driver’s motor housing

(see Fig. 9a).

Fig. 9

Fig. 9a

Use the following guidelines to arrive at a proper torque setting.

Fig. 9b

Companio

Decrease

Increase