Spectralink 1728 Benutzerhandbuch
16
R
EFERENCE
& I
NSTALLATION
M
ANUAL
J2 - EOL Definition Jumper
Jumper J2 determines the keypad zone’s EOL definition. When the jumper is OFF, EOL is disabled and the
keypad zone uses the on-board EOL resistor. When the jumper is ON, EOL is enabled and the keypad zone
requires that an external EOL resistor be connected (refer to Spectra 1738EX and 1738 Control Panel
Overview on page 7 and Spectra 1728EX and 1728 Control Panel Overview on page 8 for more details).
Jumper J2 determines the keypad zone’s EOL definition. When the jumper is OFF, EOL is disabled and the
keypad zone uses the on-board EOL resistor. When the jumper is ON, EOL is enabled and the keypad zone
requires that an external EOL resistor be connected (refer to Spectra 1738EX and 1738 Control Panel
Overview on page 7 and Spectra 1728EX and 1728 Control Panel Overview on page 8 for more details).
J2 OFF - EOL disabled
J2 ON - EOL enabled
J2 ON - EOL enabled
3.4
PROGRAMMING USING A PARADOX MEMORY KEY
Copy the sections of one Spectra control panel into the Paradox Memory Key (PMC-3). Then copy the contents of
the Memory Key into as many Spectra control panels as needed. Each panel is programmed in less than 3 seconds.
the Memory Key into as many Spectra control panels as needed. Each panel is programmed in less than 3 seconds.
Download to DESTINATION Control Panel
1) Remove AC and battery power from the control panel.
2) Place the Memory Key on the serial connector labeled
1) Remove AC and battery power from the control panel.
2) Place the Memory Key on the serial connector labeled
KEY
of the Spectra Control Panel
that is to receive the contents of the Memory Key.
3) Reapply AC and battery power.
4) In installer programming mode, enter section [900], then press [
4) In installer programming mode, enter section [900], then press [
ENTER
] to acknowledge.
5) When the keypad emits a Confirmation Beep, remove the Memory Key.
6) Enter section [750] to reprogram the modules with the information downloaded from the Paradox Memory Key.
6) Enter section [750] to reprogram the modules with the information downloaded from the Paradox Memory Key.
Copy to Memory Key from SOURCE Control Panel
1) Remove AC and battery power from the control panel.
2) Place Memory Key on the serial connector labeled
1) Remove AC and battery power from the control panel.
2) Place Memory Key on the serial connector labeled
KEY
of the Spectra Control Panel that
you want to copy. Make sure the write protect jumper of the Memory Key is on.
3) Reapply AC and battery power.
4) In installer programming mode, enter section [902], then press [
4) In installer programming mode, enter section [902], then press [
ENTER
] to acknowledge.
5) When the keypad emits a Confirmation Beep, remove the Memory Key. Remove the
Memory Key’s jumper if you do not wish to accidentally overwrite its contents.
Figure 3.2: Paradox Memory Key
PART 4: ACCESS CODES
The Spectra Series control panels support the following access codes:
INSTALLER CODE:
Used to program all control panel settings except User Access Codes.
SYSTEM MASTER CODE (001)
Provides full access. Arm and disarm using any method described in the User Code
Options in section 4.4 as well as program the User Access Codes.
Master Code 1 (002):
Permanently assigned to partition 1. Same as a regular User Code except it can
also program access codes for User Codes assigned to partition 1.
also program access codes for User Codes assigned to partition 1.
Master Code 2 (003):
Permanently assigned to partition 2. Same as a regular User Code except it can
program access codes for User Codes assigned to partition 2. If the system is not
partitioned Master Code 002 will be assigned to partition 1.
program access codes for User Codes assigned to partition 2. If the system is not
partitioned Master Code 002 will be assigned to partition 1.
45 User Codes (004 to 048):
Can arm and disarm as per User Code Options in section 4.4.