Spectralink 1728 Benutzerhandbuch
S
PECTRA
S
ERIES
35
8.2.10 S
YSTEM
T
ROUBLE
R
EPORT
C
ODES
Section [205] to [207]
Whenever the system generates one of the instances listed below, the control panel can send the
appropriate report code to the central station identifying the type of system trouble.
appropriate report code to the central station identifying the type of system trouble.
Section [205]
• Future use
•
• Future use
•
AC F
AILURE
: The control panel has detected a loss of AC power. Transmission of this report code can
be delayed (see Power Failure Report Delay on page 39).
•
B
ATTERY
F
AILURE
: backup battery is disconnected or battery voltage is
≤10.5V.
•
A
UXILIARY
S
UPPLY
: Auxiliary power supply has overloaded (current consumption is >1.1A).
Section [206]
•
•
B
ELL
O
UTPUT
O
VERLOAD
: Bell/siren output has overloaded (see page 10).
•
B
ELL
O
UTPUT
D
ISCONNECTED
: Devices connected to the Bell Output have been disconnected.
•
T
IMER
L
OSS
: The control panel has detected a loss in time or clock failure (see page 44)
•
F
IRE
L
OOP
T
ROUBLE
: The control panel has detected a tamper trouble on a fire zone.
Section [207]
•
•
W
IRELESS
L
OW
B
ATTERY
: The battery voltage of a Liberator or Omnia wireless transmitter (motion
detector or contact switch) has dropped below recommended limits.
•
M
ODULE
F
AULT
: Will report if all keypads connected to the control panel have been disconnected or if a
module with its corresponding supervision option enabled in the control panel (see pages 45 and 46) is
disconnected.
disconnected.
•
P
RINTER
F
AULT
: An error has occurred on the Printer Bus Module.
•
F
AIL
T
O
C
OMMUNICATE
: The control panel has failed all attempts to communicate with the central
station. The report code will be transmitted upon the next successful attempt.
8.2.11 S
YSTEM
T
ROUBLE
R
ESTORE
C
ODES
Sections [208] to [210]
Whenever the system restores one of the troubles listed in section 8.2.10, the control panel can send the
appropriate report code to the central station identifying the type of system trouble restore. If Telephone
Line Monitoring is enabled (see page 40), the control panel can also transmit a TLM Restore report code.
appropriate report code to the central station identifying the type of system trouble restore. If Telephone
Line Monitoring is enabled (see page 40), the control panel can also transmit a TLM Restore report code.
8.2.12 S
PECIAL
R
EPORTING
C
ODES
Sections [211] to [213]
Whenever the system generates one of the instances listed below, the control panel can send the
appropriate report code to the central station identifying the type of system occurrence.
appropriate report code to the central station identifying the type of system occurrence.
Section [211]
•
•
C
OLD
S
TART
: The control panel was completely shutdown (no battery, no AC) and then was re-started.
•
T
EST
R
EPORT
: A test report has been generated automatically (see page 39).
• Not available
•
•
P
C
E
XIT
: The control panel has ended communication with WinLoad.
Section [212]
•
•
I
NSTALLER
I
N
: Installer has entered the programming mode.
•
I
NSTALLER
O
UT
: Installer has exited the programming mode.
• Future use
• Future use
• Future use
Section [213]
•
•
T
X
S
UPERVISION
L
OSS
: Wireless Transmitter Supervision (see SPC-319 Instruction Sheet) has been
enabled and a transmitter is no longer communicating with the system.
•
T
X
S
UPERVISION
R
ESTORE
: Reports when the above trouble has been restored
• Future use
• Future use
• Future use