ATTO Technology 1550D Benutzerhandbuch
5
ATTO Technology Inc. iPBridge Installation and Operation Manual
2 Installation
If you have not already completed the instructions on the Quick Start packed with your iPBridge, use
the following instructions to install the iPBridge.
the following instructions to install the iPBridge.
Unpacking the packing box; verifying
contents
contents
• The
iPBridge
Note the serial number of your iPBridge,
located on the bottom of the unit, for later use:
____________________________________
located on the bottom of the unit, for later use:
____________________________________
• Power
cord
• Power
brick
Installing the iPBridge
1
Place the iPBridge on a stable flat surface.
2
Connect the host computer to the Ethernet port.
3
Connect SCSI devices to the iPBridge using the
proper SCSI cables. For details refer to
proper SCSI cables. For details refer to
4
Power up the SCSI devices. Proper termination
is required.
is required.
Note
You must power up attached devices before
adding power to the iPBridge.
adding power to the iPBridge.
5
6
Connect the AC power cord from the iPBridge
to the proper AC source outlet, connect the AC
power cord to the power brick and connect the
brick to the iPBridge.
to the proper AC source outlet, connect the AC
power cord to the power brick and connect the
brick to the iPBridge.
CAUTION
CAUTION
The power source must be connected to a
protective earth ground and comply with
local electrical codes. Improper grounding
may result in an electrical shock or damage
to the unit.
protective earth ground and comply with
local electrical codes. Improper grounding
may result in an electrical shock or damage
to the unit.
7
Wait for the iPBridge Ready LED to light
indicating the bridge has completed its power-
on self test sequence.
indicating the bridge has completed its power-
on self test sequence.
8
Windows
®
users continue to
®
users continue to
Installing Windows drivers
1
Windows automatically detects the iPBridge
and asks for the driver in the Add Hardware
wizard. Select Install from a list or specific
location
and asks for the driver in the Add Hardware
wizard. Select Install from a list or specific
location
2
Click Next
3
Choose Don’t Search
4
Click Next
5
Choose Have disk
6
Specify the driver as found in the PC folder in
the setup CD. The files are in a folder based on
your operating system: Win2K drivers for
Windows 2000 and Windows XP/2003 drivers
for all 2003 Server products.
the setup CD. The files are in a folder based on
your operating system: Win2K drivers for
Windows 2000 and Windows XP/2003 drivers
for all 2003 Server products.
Note
Use the files directly from the CD or copy them
onto a floppy or to a local directory on your
hard drive.
onto a floppy or to a local directory on your
hard drive.
7
Follow the remaining instructions to complete
the installation procedure.
the installation procedure.
8
After the driver is installed, the iPBridge is listed
in the System Devices folder.
in the System Devices folder.
Discovering the IP address.
1
From the CD supplied with your iPBridge, run
the QuickNav Utility QuickNAV-windows.exe
for Windows or QuickNAV-Mac for Mac OS X.
the QuickNav Utility QuickNAV-windows.exe
for Windows or QuickNAV-Mac for Mac OS X.
2
Locate the iPBridge with the serial number
recorded earlier.
recorded earlier.
3
Highlight the serial number.
4
Click Next.
If a DHCP server is available on your network,
an address is assigned automatically by the
server. Note the assigned address:
server. Note the assigned address:
_____________________________________
If you do not have a DHCP server, get an IP
If you do not have a DHCP server, get an IP
address and subnet mask from your network
administrator, type it into the area provided, and
select Next. Note the IP address and subnet
mask here._____________________________
administrator, type it into the area provided, and
select Next. Note the IP address and subnet
mask here._____________________________
5
Click on Launch Browser
Your browser points to the ATTO ExpressNAV
splash screen.