Elektra Beckum TKHS 315 E/P Benutzerhandbuch
22
ENGLISH
Operation without a dust collector is only
possible:
possible:
−
outdoors;
−
for short-term operation
(up to a maximum of 30 minutes);
(up to a maximum of 30 minutes);
−
with dust respirator.
A
Caution!
If no dust collector is hooked
If no dust collector is hooked
up the sliding plate on the chip case
must be opened, otherwise chips and
saw dust build up inside the chip
case.
must be opened, otherwise chips and
saw dust build up inside the chip
case.
To open the sliding plate:
1.
Loosen both nuts (66) on the under-
side of the chip case slightly.
side of the chip case slightly.
2.
Slide sliding plate (67) to the side.
3.
Tighten nuts (66).
7.2
Setting the depth of cut
A
Danger!
Parts of the body or objects in
Parts of the body or objects in
the setting range can be caught be
the running saw blade! Set the depth
of cut only with the saw blade at
standstill!
the running saw blade! Set the depth
of cut only with the saw blade at
standstill!
The saw blade's cutting height needs to
be adapted the the height of the work-
piece: the blade guard shall rest with its
front edge on the workpiece.
be adapted the the height of the work-
piece: the blade guard shall rest with its
front edge on the workpiece.
•
Set the depth of cut by turning the
handwheel (68) on the chip case.
handwheel (68) on the chip case.
3
Note:
To compensate for possible play
To compensate for possible play
in the blade height setting mechanism,
always raise the blade to the desired
position.
always raise the blade to the desired
position.
7.3
Setting the saw blade tilt
A
Danger!
Parts of the body or objects in
Parts of the body or objects in
the setting range can be caught by
the running saw blade!Set the depth
of cut only with the saw blade at
standstill!!
the running saw blade!Set the depth
of cut only with the saw blade at
standstill!!
The saw blade tilt is steplessly adjusta-
ble between 0
ble between 0
°
and 45
°
.
1.
Loosen twist handle (69) approx.
one turn.
one turn.
2.
Set required blade tilt with the blade
tilt lever (70).
tilt lever (70).
3.
Lock the set bevel angle by tighten-
ing the twist handle again.
ing the twist handle again.
7.4
Sawing with the rip fence
3
Note:
When sawing with the rip fence
When sawing with the rip fence
the long fence extrusion must be used.
1.
Adopting the fence extrusion to the
workpiece height:
workpiece height:
−
Wide edge (71) =
for cutting thick stock
for cutting thick stock
−
Small edge (72) =
for cutting thin stock
for cutting thin stock
2.
The rip fence (73) is placed from top
onto the guide extrusion (74) at the
front of the saw and locked with the
lock lever (75).
onto the guide extrusion (74) at the
front of the saw and locked with the
lock lever (75).
A
Danger!
Always use the push stick if
Always use the push stick if
the distance between saw blade and
rip fence is less than 120 mm.
rip fence is less than 120 mm.
3.
Set the cutting height of the saw
blade. The blade guard must rest
with its front edge on the workpiece.
blade. The blade guard must rest
with its front edge on the workpiece.
4.
Set saw blade tilt and lock.
5.
Start motor.
6.
Cut workpiece in a single pass.
7.
Switch machine off if no further cut-
ting is to be done immediately after-
wards.
ting is to be done immediately after-
wards.
7.5
Sawing with the mitre
fence
fence
1.
Swing mitre fence on the table top.
2.
Set to desired mitre angle and lock
in that position. For mitre cuts, the
fence extrusion is adjustable to 45
in that position. For mitre cuts, the
fence extrusion is adjustable to 45
°
maximum.
67
66
68
69
70
71
72
73
74
75