Elektra Beckum TKHS 315 E/P Benutzerhandbuch
24
ENGLISH
9.4
Maintenance
Before switching ON
Visual check if distance saw blade – riv-
ing knife is 3...8 mm.
ing knife is 3...8 mm.
Visual check of power cable and power
cable plug for damage; if necessary
have damaged parts replaced by a qual-
ified electrician.
cable plug for damage; if necessary
have damaged parts replaced by a qual-
ified electrician.
After switching OFF
Check to see if the saw blade post-runs
for more than 10 seconds; if so, have the
electronic motorbrake replaced by a
qualified electrician.
for more than 10 seconds; if so, have the
electronic motorbrake replaced by a
qualified electrician.
Monthly (if used daily)
Remove saw dust and chips with vac-
uum or brush; apply light coat of oil to
guide elements:
uum or brush; apply light coat of oil to
guide elements:
−
threaded rod and guide rods of
blade rise and fall mechanismn:
blade rise and fall mechanismn:
−
swivel segments.
Every 300 hours of operation
Check all screwed joints, retighten if
necessary.
necessary.
A
Danger!
Repairs to electric tools must
Repairs to electric tools must
be carried out by qualified electri-
cians only!
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
the electric tool.
•
Lower saw blade fully.
•
Dismount add-on parts (fence, slid-
ing carriage, table extension).
ing carriage, table extension).
•
If possible use original carton for
shipping.
shipping.
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
ries are available at your specialized
dealer – see back cover for illustrations:
A
Universal Wheel Set
For easy moving.
B
Sliding Carriage
For convenient guiding of long
stock.
For convenient guiding of long
stock.
C
Table Side Extension, right
Table size 1000 mm x 600 mm;
with foldable supports.
Table size 1000 mm x 600 mm;
with foldable supports.
D
Suction Adapter to connect a shop
vacuum to the dust collection
attachment.
vacuum to the dust collection
attachment.
E
Care and Maintenance Spray to
remove resin residue and preserve
metal surfaces.
remove resin residue and preserve
metal surfaces.
F
Saw blade CV 315 x 1.8 x 30
56 multiple combination teeth
for solid wood and particle board.
56 multiple combination teeth
for solid wood and particle board.
G
Saw blade CV 315 x 1.8 x 30
80 neutral multiple teeth
for especially smooth cuts in solid
wood and particle board.
80 neutral multiple teeth
for especially smooth cuts in solid
wood and particle board.
H
Saw blade TCT 315 x 2.8 x 30
48 universal alternate bevel teeth
for all woods and wood-derived
smaterials.
48 universal alternate bevel teeth
for all woods and wood-derived
smaterials.
I
Roller Stand RS 420
J
Roller Stand RS 420 W
K
Roller Stand RS 420 G
The saw's packing can be 100% recy-
cled.
cled.
Worn out electric tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
rine-free bleached paper.
A
Danger!
Before carrying out any fault
Before carrying out any fault
service or maintenance work, always:
1.
switch machine OFF;
2.
unplug power cable;
3.
wait for saw blade to come to
standstill.
standstill.
Check that all safety devices are
operational again after each fault
service.
operational again after each fault
service.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
ure:
−
switch on again.
No mains voltage:
−
check cables, plug, outlet and mains
fuse.
fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
blade or chip build-up in the chip case:
−
remove cause for overheating, wait
for a few minutes, then start saw
again.
for a few minutes, then start saw
again.
Motor supply voltage too low:
−
use a shorter extension cable or
extension cable with larger lead
cross section
(
extension cable with larger lead
cross section
(
≥
1.5 mm
2
).
−
Have power supply checked by a
qualified electrician.
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
marks on blade body):
−
replace saw blade (see chapter
"Care and maintenance").
"Care and maintenance").
Chip build-up in the chip case
No, or dust collector of insufficient
capacity connected (see "Dust collector"
in chapter "Operation"):
capacity connected (see "Dust collector"
in chapter "Operation"):
−
connect dust collector, or
−
increase suction capacity.
Sliding plate of chip case closed:
−
open sliding plate
Height adjustment mechanism of saw
blade working stiff
blade working stiff
Spindle of height adjustment mechanism
gummy:
gummy:
−
clean spindle and spray with Care
and Maintenance Spray (see chap-
ter "Care and maintenance").
and Maintenance Spray (see chap-
ter "Care and maintenance").
10. Repairs
11. Transportation
12. Available accessories
13. Environmetal protection
14. Trouble shooting