Cisco Systems OL-6426-02 Benutzerhandbuch
B E TA D R A F T - C I S C O C O N F I D E N T I A L
14-7
Cisco 1800 Series Integrated Services Routers (Fixed) Software Configuration Guide
OL-6426-02
Chapter 14 Troubleshooting
ATM Troubleshooting Commands
Example 14-4 Viewing ATM Errors
Router# debug atm errors
ATM errors debugging is on
Router#
01:32:02:ATM(ATM0.2):VC(3) Bad SAP received 4500
01:32:04:ATM(ATM0.2):VC(3) Bad SAP received 4500
01:32:06:ATM(ATM0.2):VC(3) Bad SAP received 4500
01:32:08:ATM(ATM0.2):VC(3) Bad SAP received 4500
01:32:10:ATM(ATM0.2):VC(3) Bad SAP received 4500
debug atm events Command
Use the debug atm events command to display events that occur on the ATM interface processor and to
diagnose problems in an ATM network. This command provides an overall picture of the stability of the
network. The no form of this command disables debugging output.
diagnose problems in an ATM network. This command provides an overall picture of the stability of the
network. The no form of this command disables debugging output.
If the interface is successfully communicating with the Digital Subscriber Line Access Multiplexer
(DSLAM) at the telephone company, the modem state is 0x10. If the interface is not communicating with
the DSLAM, the modem state is 0x8.
(DSLAM) at the telephone company, the modem state is 0x10. If the interface is not communicating with
the DSLAM, the modem state is 0x8.
shows an ADSL line that is up and communicating
successfully.
shows an ADSL line that is not communicating correctly. Note that the
modem state does not transition to 0x10.
Example 14-5 Viewing ATM Interface Processor Events—Success
Router# debug atm events
Router#
00:02:57: DSL: Send ADSL_OPEN command.
00:02:57: DSL: Using subfunction 0xA
00:02:57: DSL: Using subfunction 0xA
00:02:57: DSL: Sent command 0x5
00:02:57: DSL: Received response: 0x26
00:02:57: DSL: Unexpected response 0x26
00:02:57: DSL: Send ADSL_OPEN command.
00:02:57: DSL: Using subfunction 0xA
00:02:57: DSL: Using subfunction 0xA
00:02:57: DSL: Sent command 0x5
00:03:00: DSL: 1: Modem state = 0x8
00:03:02: DSL: 2: Modem state = 0x10
00:03:05: DSL: 3: Modem state = 0x10
00:03:07: DSL: 4: Modem state = 0x10
00:03:09: DSL: Received response: 0x24
00:03:09: DSL: Showtime!
00:03:09: DSL: Sent command 0x11
00:03:09: DSL: Received response: 0x61
00:03:09: DSL: Read firmware revision 0x1A04
00:03:09: DSL: Sent command 0x31
00:03:09: DSL: Received response: 0x12
00:03:09: DSL: operation mode 0x0001
00:03:09: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME]
Example 14-6 Viewing ATM Interface Processor Events—Failure
Router# debug atm events
Router#
00:02:57: DSL: Send ADSL_OPEN command.
00:02:57: DSL: Using subfunction 0xA
00:02:57: DSL: Using subfunction 0xA