Enterasys 6a000 Verweisanleitung
1-6 SmartCell 6A000/ZX-250 Reference Manual
Introduction
Operators
Parameters appear in the parameter tables in the same order and spelling as the switch shows them.
Most switch attribute descriptions show two tables—Input Parameter and Output Parameter. If the parameter has
already been described in the input parameter table, no reference to it appears in the output parameter table. The output
parameter table contains only parameters that have not been described in the input parameter table or that are written
very differently on output despite having the same meaning.
already been described in the input parameter table, no reference to it appears in the output parameter table. The output
parameter table contains only parameters that have not been described in the input parameter table or that are written
very differently on output despite having the same meaning.
Only one parameter table in a switch attribute section means either that switch attribute uses only input parameters or
that the output parameters are identical to the input parameters. The heading of the table indicates which is the case. If
the table heading says Input Parameter or Output Parameter, only input or output parameters apply to this switch
attribute. However, if the table heading says Parameter, the table contains both input and output parameters, and their
field names and definitions are identical.
that the output parameters are identical to the input parameters. The heading of the table indicates which is the case. If
the table heading says Input Parameter or Output Parameter, only input or output parameters apply to this switch
attribute. However, if the table heading says Parameter, the table contains both input and output parameters, and their
field names and definitions are identical.
Some output parameters show either (</d>) or (</s>) to indicate that a filter flag is available and that parameter is
available only when you type either /d (detailed information) or /s (summarized information) after the command. If
you do not type these command extensions, the parameters do not appear. Further explanations are given at relevant
sections. See “PVC” for an example.
available only when you type either /d (detailed information) or /s (summarized information) after the command. If
you do not type these command extensions, the parameters do not appear. Further explanations are given at relevant
sections. See “PVC” for an example.
The following table gives details about several of the most common parameters in this manual; a shorter description
of these parameters appears at the relevant sections within the manual:
of these parameters appears at the relevant sections within the manual:
:"*dF˜s_¢
3zF•"›p•˜:"*dF˜'¨zd"m"›apm
6"•"hF›F•
&F’4•az›apm
="d¤F—)aFd=˜9a«F
&FO"¤d›
[Input or Output Field]
(</d>)
(</d>)
What the switch puts on your screen (either as input
or output) relating to the console command you are
executing. The [InputParameter] is an entry you
need to complete if you do not accept the default.
The [OutputParameter] shows information from the
switch. Requires no input. This example is available
only within the detailed information table.
or output) relating to the console command you are
executing. The [InputParameter] is an entry you
need to complete if you do not accept the default.
The [OutputParameter] shows information from the
switch. Requires no input. This example is available
only within the detailed information table.
Unit of measurement/
Maximum field size
for input entry.
Maximum field size
for input entry.
Option
offered by
the switch.
offered by
the switch.
:"*dF˜s_•
6"•"hF›F•˜:"*dF˜'¨zd"m"›apm
6"•"hF›F•
&F’4•az›apm
="d¤F—)aFd=˜9a«F
&FO"¤d›
[PortNumber]
Port number on the switch. Port
numbers can be any of the physical
ports on the local switch. Specifying
"ALL" causes all related values for the
ports to be affected by the command.
numbers can be any of the physical
ports on the local switch. Specifying
"ALL" causes all related values for the
ports to be affected by the command.
Port B4 is the CPU port. The
SmartCell 6A000/ZX-250 reserve
this port for use by the CPU for local
servers and clients. Therefore, B4
port is usually not listed. Only ALL,
A1-A4, B1-B3, C1-C4, and D1-D4
are listed.
SmartCell 6A000/ZX-250 reserve
this port for use by the CPU for local
servers and clients. Therefore, B4
port is usually not listed. Only ALL,
A1-A4, B1-B3, C1-C4, and D1-D4
are listed.
ALL or A1