Sharp AR-M162 Betriebsanweisung
12
COPY SETTINGS
These programs are used to enable various copy
functions. To access one of these programs, select
"COPIER" in the mode selection screen, select the
desired program in the copy settings screen, and
press the [OK] key.
functions. To access one of these programs, select
"COPIER" in the mode selection screen, select the
desired program in the copy settings screen, and
press the [OK] key.
EXPOSURE ADJUST
This program is used to adjust the exposure level
when "AUTO" is used for the exposure mode. The
auto exposure level can be set separately for the
document glass and the SPF.
One of five levels can be selected, with the left end of
the scale the lightest level and the right end of the
scale the darkest level.
The factory default setting is the middle level.
when "AUTO" is used for the exposure mode. The
auto exposure level can be set separately for the
document glass and the SPF.
One of five levels can be selected, with the left end of
the scale the lightest level and the right end of the
scale the darkest level.
The factory default setting is the middle level.
Select "EXPOSURE ADJUST" and press the [OK] key.
The following screen will appear.
The following screen will appear.
1
Select "PLATEN" or "SPF/RSPF" with the
[
[
] or [
] key.
2
Press the [
] or [
] key to adjust the
exposure.
3
Repeat steps 1 and 2 to adjust the other
exposure.
exposure.
4
Press the [OK] key.
MARGIN DEFAULT
This is used to set the default margin width.
The factory default setting is "1/2 inch (10 mm)".
The factory default setting is "1/2 inch (10 mm)".
Select "MARGIN DEFAULT" and press the [OK] key.
The following screen will appear.
The following screen will appear.
1
Adjust the default margin width with the
[
[
] or [
] key.
The width can be set from 0" to 1" in increments of 1/4"
(0 to 20 mm in increments of 5 mm).
(0 to 20 mm in increments of 5 mm).
2
Press the [OK] key.
ERASE ADJUST
This is used to set the default erasure width.
The factory default setting is "1/2 inch (10 mm)".
The factory default setting is "1/2 inch (10 mm)".
Select "ERASE ADJUST" and press the [OK] key. The
following screen will appear.
following screen will appear.
1
Adjust the edge erase and center erase
width with the [
width with the [
] or [
] key.
The edge erase width and the center erase width share
the same default value, which can be set from 0" to 1" in
increments of 1/4" (0 to 20 mm in increments of 5 mm).
the same default value, which can be set from 0" to 1" in
increments of 1/4" (0 to 20 mm in increments of 5 mm).
2
Press the [OK] key.
CARD SHOT DEFAULT
This program is used to set the default dimensions that
appear when the card shot size entry screen is displayed.
The factory default settings are 3-3/8" (86 mm) for the
width (X) and 2-1/8" (54 mm) for the length (Y).
appear when the card shot size entry screen is displayed.
The factory default settings are 3-3/8" (86 mm) for the
width (X) and 2-1/8" (54 mm) for the length (Y).
Select "CARD SHOT DEFAULT" and press the [OK]
key. The following screen will appear.
key. The following screen will appear.
1
Select X or Y with the [
] or [
] key and
adjust the corresponding default value
with the [
with the [
] or [
] key.
2
Press the [OK] key.
DEFAULT TRAY SET
This program is used to set which tray is selected by
default.
Trays that appear for selection will vary depending on
the optional trays that have been installed.
The factory default setting is "TRAY 1".
default.
Trays that appear for selection will vary depending on
the optional trays that have been installed.
The factory default setting is "TRAY 1".
EXPOSURE ADJUST
PLATEN
SPF/RSPF
MARGIN DEFAULT
inch
(0~1)
ERASE ADJUST
inch
(0~1)
CARD SHOT DEFAULT
SIZE(inch)
X:
Y:
SIZE(inch)
X:
Y:
01_Keyope.fm 12 ページ ２００６年２月２１日 火曜日 午後３時３９分