Vinotemp wm-125c Anleitung Für Quick Setup
WM-125C
Wine Cellar Warning Caller
Quick Start Guide
1. PROGRAMMING REGULAR PHONE NUMBERS
The caller can call up to 4 regular phone numbers per
zone. To program the numbers to be called when zone 1
(Z1) is in alarm:
• Press
zone. To program the numbers to be called when zone 1
(Z1) is in alarm:
• Press
- this selects location 1.
• After the dial LED flashes twice, enter phone number to
dial.
•••• Finish by pressing .
Example:
- this would dial phone
number
555-1212 and deliver the message programmed for
zone 1.
Program the remaining phone numbers (2, 3 and 4) as
above. For example:
• Press
above. For example:
• Press
- this selects location 2.
• After the dial LED flashes twice, enter phone number to
dial.
• Finish by pressing .
Program numbers for zone 2 (Z2) in the same manner,
except that the location numbers will be 5, 6, 7, & 8. Start
with pressing
Program numbers for zone 2 (Z2) in the same manner,
except that the location numbers will be 5, 6, 7, & 8. Start
with pressing
- this selects location 5.
2. PROGRAMMING NUMERIC PAGERS
Pagers require two phone number locations. Therefore,
each WM-125C zone can call a maximum of two pagers.
Proceed as follows to program pagers into zone 1:
• Press
each WM-125C zone can call a maximum of two pagers.
Proceed as follows to program pagers into zone 1:
• Press
- this selects location 1.
• After the dial LED flashes twice, enter the phone number of
the numeric pager.
• Press
- this links the current location with the next
for pager function.
• Press .
• Press
• Press
- this selects location 2.
• After the dial led flashes twice, press
- this links this
location to the previous location for pager function.
• Press
to provide a 10-second delay allowing the
paging company to pick up (you can enter any two digit
value, but 10 seconds works in most cases).
value, but 10 seconds works in most cases).
• Enter the number you wish to appear on the pager’s
display and finish by pressing
.
Example:
and then:
- this would deliver
the message “9999” to a pager at phone No. 555-2525.
If you wish to program another pager in zone 1, follow these
same steps, but use locations 3 and 4. To program pagers
into zone 2, use locations 5 & 6 and/or locations 7 & 8.
same steps, but use locations 3 and 4. To program pagers
into zone 2, use locations 5 & 6 and/or locations 7 & 8.
3. RECORDING VOICE MESSAGES
The WM-125C contains three locations for voice
messages. The total recording time can not exceed 20
seconds, or 15 seconds for one message.
messages. The total recording time can not exceed 20
seconds, or 15 seconds for one message.
Message AL-1 is the alarm type message for zone 1 (burglar
alarm activation, for example).
alarm activation, for example).
Message AL-2 is the alarm type message for zone 2 (low
temperature detection, for example).
temperature detection, for example).
Message AL-1 & AL-2 is the location message (name and
address - common to AL-1 and AL-2).
address - common to AL-1 and AL-2).
To record AL-1 message:
• Press
• Press and hold
• Press and hold
while reading the message aloud - red
LED will be on.
• Release
and press - red LED will turn off.
To record AL-2 message:
• Press
• Press and hold
• Press and hold
while reading the message aloud - red
LED will be on.
• Release
and press - red LED will turn off.
To record AL-1 & AL-2 (location message):
• Press
• Press and hold both
• Press and hold both
and
buttons at the same
time while reading the message aloud - red LED will be on.
• Release
and
and press - red LED will turn off.
For more advanced applications, refer to the WM-125C installation instructions, or contact the Vinotemp.
Vinotemp International
17631 S Susana Rd., Rancho Dominguez, CA 90221
Tel: (310) 886-3332 Fax: (310) 886-3310 Email: info@vinotemp.com
Page 1