Delfield 8100-ef Installationsanweisungen
N8000 Series Drop-In Installation and Operation Manual
For customer service, call (800) 733-8829, (800) 733-8821, Fax (989) 773-3210, www.delfield.com
6
Drop In Procedure
These units are intended for indoor use only. A room
temperature of not more than 86°F (30°C) is recommended.
Reinforce the counter as necessary to provide maximum
loading.
temperature of not more than 86°F (30°C) is recommended.
Reinforce the counter as necessary to provide maximum
loading.
Unit requires that the sides and bottom are not
any closer than 3” to any combustible material.
any closer than 3” to any combustible material.
The counter cut-out sizes and power requirements are shown
on pages 3-5. A gasket is installed in the flange of each unit.
The weight of the unit on the gasket forms a seal preventing
liquids from seeping into the cut-out opening.
on pages 3-5. A gasket is installed in the flange of each unit.
The weight of the unit on the gasket forms a seal preventing
liquids from seeping into the cut-out opening.
Louvers
Self-contained refrigerated units (N8100, N800 and N800G
Series) require airflow to the compressor. A 13” x 5” louver
is (33 cm x63.5 cm) provided by Delfield and must be installed
in the counter in front of the condenser. See specifications on
page 3 for louver cutout dimensions. The rear must have an
opening to permit removal of heated air. The opening must be
at least 8” x 11”, a total of 88 square inches (0.3 cm x 7.9 cm,
a total of 566 square centimeters).
Series) require airflow to the compressor. A 13” x 5” louver
is (33 cm x63.5 cm) provided by Delfield and must be installed
in the counter in front of the condenser. See specifications on
page 3 for louver cutout dimensions. The rear must have an
opening to permit removal of heated air. The opening must be
at least 8” x 11”, a total of 88 square inches (0.3 cm x 7.9 cm,
a total of 566 square centimeters).
Plumbing
The unit’s drain must have an outlet to an appropriate drainage
area or container. N800 series have 1/” drain and N800G
series have 3/4” drain located on end/center. The 1” diameter
drain on N8000, N8100, 8100FA and 8100EF Series units is
shipped loose and must be connected during installation.
area or container. N800 series have 1/” drain and N800G
series have 3/4” drain located on end/center. The 1” diameter
drain on N8000, N8100, 8100FA and 8100EF Series units is
shipped loose and must be connected during installation.
Moisture collecting from improper drainage
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
responsibility to provide a container or outlet
for drainage.
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
responsibility to provide a container or outlet
for drainage.
Some N8000, N8000N, N8100B and N8100NB
may have poyethylene insulation in the drain
hole. This can easily be cut out without
any contact or damage to the units interior
insulation or refrigeration lines.
may have poyethylene insulation in the drain
hole. This can easily be cut out without
any contact or damage to the units interior
insulation or refrigeration lines.
Electrical connection
Refer to the amperage data on pages 3-5, the serial tag or
your local code to be sure the unit is connected to the proper
power source. A protected circuit of the correct voltage and
amperage must be run for connection of the line cord.
Some units have an “ON/OFF” switch located behind the
Some units have an “ON/OFF” switch located behind the
louvered panel in the machine compartment. Simply turn the
switch to “ON” to begin operation.
Some units have an “OFF” position on the switch which is
Some units have an “OFF” position on the switch which is
located behind the louvered panel in the machine compart-
ment. Simply turn the dial to begin operation.
The unit must be disconnected from the
power source whenever performing service or
power source whenever performing service or
maintenance functions.
Never operate the unit without the louvered
panel in place!
panel in place!
CAUTION
Installation N8000, N8000N, N8100B, N8100NB, N8200, N8200G, N8100-FA & 8100-EF Series
D A N G E R
Drop In Procedure
These units are intended for indoor use only. Reinforce the
counter as necessary to provide maximum loading.
counter as necessary to provide maximum loading.
Unit requires that the sides and bottom are not
any closer than 3” to any combustible material.
any closer than 3” to any combustible material.
The counter cut-out sizes and power requirements are shown
on pages 3-5. A gasket is installed in the flange of each unit.
The weight of the unit on the gasket forms a seal preventing
liquids from seeping into the cut-out opening.
on pages 3-5. A gasket is installed in the flange of each unit.
The weight of the unit on the gasket forms a seal preventing
liquids from seeping into the cut-out opening.
N8700-D Series pans should be installed with the drains at the
back, away from the operator’s sides. N8700N Series have
drains located in the front - operator side.
back, away from the operator’s sides. N8700N Series have
drains located in the front - operator side.
The controls on N8700-D and N8800 Series units are mounted
in a control panel, designed to be installed at a “remote”
location. The control panel should be installed so that the
indicator light for each control is above the control. N8700 &
N8700N Series units have 48” (11.9cm) of conduit and N8800
Series units have 4” (61.0cm) of conduit between the pans and
the remote control panel to facilitate this installation.
in a control panel, designed to be installed at a “remote”
location. The control panel should be installed so that the
indicator light for each control is above the control. N8700 &
N8700N Series units have 48” (11.9cm) of conduit and N8800
Series units have 4” (61.0cm) of conduit between the pans and
the remote control panel to facilitate this installation.
Plumbing
N8700-D and N8700N Plumbing: Unit is equipped with 1/”
drains, (one per well located in right rear corner 1/” female
N.P.T.) manifold and 1/” gate valve.
N8800 Plumbing: Well is sloped to a 1.00” female N.P.T.
stainless steel drain.
drains, (one per well located in right rear corner 1/” female
N.P.T.) manifold and 1/” gate valve.
N8800 Plumbing: Well is sloped to a 1.00” female N.P.T.
stainless steel drain.
Moisture collecting from improper drainage
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
and operator’s responsibility to provide a
can create a slippery surface on the floor
and a hazard to employees. It is the owner’s
and operator’s responsibility to provide a
container or outlet for drainage.
Electrical connection
Refer to the amperage data on pages 3-5, the serial tag or
your local code to be sure the unit is connected to the proper
power source.
The unit must be disconnected from the
power source whenever performing service
power source whenever performing service
or maintenance functions.
CAUTION
D A N G E R
Installation N8700D, N8700N, & N8800 Series