LXE mx6 Verweisanleitung
206
Power Tools EZConfig Utilities
MX6 Reference Guide
E-EQ-MX6RG-E
Key Value
Description
AimerDelayALR
500
Similar to AimerDelay, but for ALR mode only
Trigger 42
Default: 42
(On/Scan Key)
(On/Scan Key)
Sets the key used by ScanDemo to initiate a
scan/decode. The key is registered as a system hot
key, it cannot be registered as a hot key by any
other applications.
scan/decode. The key is registered as a system hot
key, it cannot be registered as a hot key by any
other applications.
ScanTimeout 9000
Default: 2000
(2 seconds)
(2 seconds)
Specifies the decode time out in 1/1000th seconds.
If a barcode is not decoded within the specified
timeout period an audio and visual notification
will indicate that an error occurred.
If a barcode is not decoded within the specified
timeout period an audio and visual notification
will indicate that an error occurred.
ScanAbort
1
Specifes the behavior of the decoder upon release
of the trigger key.
0 = The decoder will scan as long as specified by
the ScanTimeout parameter
1 = Releasing the trigger key will cause the
decoder to stop scanning.
of the trigger key.
0 = The decoder will scan as long as specified by
the ScanTimeout parameter
1 = Releasing the trigger key will cause the
decoder to stop scanning.
ScanInterval
0
Time interval between scanning attempts
(milliseconds), when in AutoScan mode.
(milliseconds), when in AutoScan mode.
ScanMode
1
Specifies the decode mode. If 1, the decoder is in
normal mode. If 2, the decoder works in ALD
(Aggressive Linear Decode) mode.
normal mode. If 2, the decoder works in ALD
(Aggressive Linear Decode) mode.
LinearRange 3
Default: 3
Specifies the linear search range to be used while
in ALD mode. The range is 1 to 6. A value of 1
indicates a tight vertical range near the aimer. A
value of 6 indicates a vertical range of the entire
height of the imager.
in ALD mode. The range is 1 to 6. A value of 1
indicates a tight vertical range near the aimer. A
value of 6 indicates a vertical range of the entire
height of the imager.
PrintWeight
4
1-7: Sets the decoder's PrintWeight parameter:
adjusts the way the decoder reads Matrix symbols.
If the image engine will be seeing consistently
heavily printed Matrix symbols, a print weight of
6 or 7 may improve reading performance.
adjusts the way the decoder reads Matrix symbols.
If the image engine will be seeing consistently
heavily printed Matrix symbols, a print weight of
6 or 7 may improve reading performance.
ReplaceCRwithCRLF 0
0/1: If set to 1, replaces the carriage return (13) in
the decoded data with carriage return and line feed
(13,10).
0=Disable
1=Enable
the decoded data with carriage return and line feed
(13,10).
0=Disable
1=Enable
GoodScanWav
Default=””
Specifies a wave file to be played on a successful
decode/data reception. The wave file should be an
8 bit, 11KHz, mono, PCM file. If no wave file is
specified, the default beep will be utilized. Use the
‘sound’ setting to enable and disable audio
notification. NOTE: The Window's “Good
Decode” sound defined in the control panel or the
GoodScanFreq parameter take precedence over
this option, if defined.
decode/data reception. The wave file should be an
8 bit, 11KHz, mono, PCM file. If no wave file is
specified, the default beep will be utilized. Use the
‘sound’ setting to enable and disable audio
notification. NOTE: The Window's “Good
Decode” sound defined in the control panel or the
GoodScanFreq parameter take precedence over
this option, if defined.