Panasonic PV-GS36 Bedienungsanleitung

•  Is manual focus mode selected? If auto focus 

mode is selected, focus is automatically adjusted.

•  There are some recording subjects and 

surroundings for which the auto focus does not 
operate correctly. (p. 64) If so, use the manual 
focus mode to adjust the focus. (p. 38) 

•  Is the MagicPix function set? When the MagicPix 

function is working, focusing shifts into the manual 
mode.

•  Read the contents and respond to them. (p. 57)

•  The remaining tape time indication may disappear 

temporarily during Still Advance Playback or other 
operation. If you continue ordinary recording or 
playback, the indication is restored.

•  If scenes of less than 15 seconds are continuously 

recorded, the remaining tape time cannot be 
correctly displayed.

•  In some cases, the remaining tape time indication 

may show remaining tape time that is 2 to 
3 minutes shorter than the actual remaining tape 
time.

• If you set [   SETUP] >> [   DISPLAY] >> [OFF], 

indications other than the tape running condition, 
warning, and date indications disappear.

•  Is the volume too low? During playback, push 

the [–   / VOL +] lever to display the volume 
indication and adjust it. (p. 39)

•  Have you set [   SETUP] >> [   12bit AUDIO] >> 

[MIX]? If you set [   AUDIO REC] >> [12bit] and 
dub audio to a recorded tape, you can hear the 
sound on recording and the sound dubbed at a 
later time. To hear the sounds separately, set to 
[ST1] or [ST2]. (p. 39)

•  Have you set [   SETUP] >> [   AUDIO OUT] >> 

[STEREO] and reproduced a picture containing 
the main sound and sub sound? Set to [L] to hear 
main sound, and set to [R] to hear the sub sound. 
(p. 23)

•  The Camcorder cannot be operated unless you 

open the LCD Monitor or extend the Viewfinder.

•  Remove the cassette and then press the 

[RESET] button. (p. 64) If normal conditions 
are not restored yet, turn off the power. Then, 
about 1 minute later, turn on the power again. 
(Conducting the above operation when the Access 
Lamp is on may destroy the data on the card.)

•  Does the power lamp comes on when opening the 

cassette cover? (p. 14) Make sure that the battery 
and the AC adaptor are properly connected. 
(p. 11)

•  Is the battery in use discharged? Charge the 

battery and remove the cassette.

•  Close the cassette cover completely, and fully 

open it again. (p. 14)

•  Has condensation occurred? Wait until the 

condensation indication disappears. (p. 59)

•  Is the accidental erasure prevention slider on 

the cassette open? If it is open (set to [SAVE]), 
recording cannot be performed. (p. 15)

•  Is the tape wound to the end? Insert a new 

cassette.

•  Is the Recording Mode set? When in the Playback 

Mode, recording cannot be performed. (p. 25)

•  Has condensation occurred? No operation other 

than cassette removal can be performed when 
condensation occurs. Wait until the condensation 
indication disappears. (p. 59)

•  Is the cassette cover open? If the cover is open, 

the Camcorder may not operate normally. Close 
the cassette cover. (p. 14)

•  Has the demonstration started? In the Tape 

Recording mode, if you set [   DEMO MODE] 
>> [ON] without inserting a cassette or a card, 
the demonstration starts. For normal use, set this 
function to [OFF]. (p. 24)

•  Has condensation occurred? Wait until the 

condensation indication disappears.