Heartland hcdwis Betriebsanweisung

20

Gather the required tools and parts before starting 

installation.

Parts supplied
A. 2 – drain hose clamps, 1 large and 1 small
B. 2 – # 10 x 1/2” Phillips-head screws
C. drain hose

D. 2 #8 x 1-3/8” TORX®T15 screws
E. 4 #10 x 3/8” hex-head screws
F. Bottom sound pad (located in lower rack)
G. Moisture barrier tape
Make sure all these parts are included. If not included, call
1-877-650-5775.

® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

® Registered trademark of TEXTRON.

Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide 
clearance between motor and flooring. Motor should not touch the 
floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher against 
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your 
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available from 
your dealer for installing underneath the countertop, but is not 
required. This may also be obtained by calling 1-877-650-5775.
Check location where dishwasher will be installed. The location 
must provide:
• easy access to water, electricity and drain.
• convenient access for loading and unloading dishes. Corner
locations require a 2” (5.1 cm) minimum clearance between the side 
of the dishwasher door and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
NOTE:To prevent shifting during dishwasher operation, shims 
must be securely attached to the floor. 
If dishwasher will be left unused for a period of time or in a location 
where it may be subject to freezing, have it winterized by authorized 
service personnel.
Make sure pipes, wires and drain hose are within the shaded area 
shown in the “Cutout dimensions” section.
Helpful Tip: If the floor in the dishwasher opening is uneven 
(example: tile flooring only partway into opening) you will need 
to take special care in measuring dimensions and in leveling 
dishwasher.

Tools Needed:
• pliers
• Phillips screwdriver
• 5/16” and 1/4” nut drivers or
hex sockets
• measuring tape or ruler
• 10” adjustable wrench that
opens to 1-1/8” (2.9 cm)
• flat-blade screwdriver
• utility knife
• 2 twist-on wire connectors
which are the proper size 
to connect your household 
wiring to 16-gauge wiring in 
dishwasher
• small level

• flashlight
• shallow pan
• 5/8” open-end wrench
• bath towel
• wood block
Parts needed:
• 90° elbow with 3/8” N.P.T.
external threads on one end. 
(The other end must fit your 
water supply line.)
• Teflon® tape or pipe joint
compound
• shims (if installed with built-
up floor)

Tools needed:
• electric drill with 1/2”, 3/4”
and 1-1/2” hole saw bits
• small tubing cutter
• wire stripper
• 1-1/2”-2” screw-type clamp
if connecting to waste-tee

Parts needed:
• copper tubing (3/8”
recommended) or flexible 
stainless steel braided fill line
• clamp connector or conduit
connector to fit a 7/8” (2.2 cm) 
diameter hole

A

B

C

Installation Instructions