Heartland hcdwis Betriebsanweisung
22
Drain Requirements
• Use the new drain hose supplied with your dishwasher. If this is
not long enough, use a new drain hose with a maximum length
of 12 feet (3.7 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1” (2.5 cm)
drain connector of the dishwasher.
• Connect drain hose to waste tee or disposer inlet above drain trap
in house plumbing and 20” (50.8 cm) minimum above the floor.
It is recommended that the drain hose either be looped up and
securely fastened to the underside of the counter, or be connected to
an air gap.
not long enough, use a new drain hose with a maximum length
of 12 feet (3.7 m) that meets all current AHAM/IAPMO test
standards, is resistant to heat and detergent, and fits the 1” (2.5 cm)
drain connector of the dishwasher.
• Connect drain hose to waste tee or disposer inlet above drain trap
in house plumbing and 20” (50.8 cm) minimum above the floor.
It is recommended that the drain hose either be looped up and
securely fastened to the underside of the counter, or be connected to
an air gap.
• Use an air gap if the drain hose is connected to house plumbing
lower than 20” (50.8 cm) above subfloor or floor.
• Use 1/2” minimum I.D. drain line fittings.
lower than 20” (50.8 cm) above subfloor or floor.
• Use 1/2” minimum I.D. drain line fittings.
Water Supply Requirements
• A hot water line with 20-120 psi (138-862 kPa) water pressure.
• 120°F (49°C) water at dishwasher.
• 3/8” O.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2” minimum plastic tubing is not
recommended).
• A 90° elbow with 3/8” N.P.T. external pipe threads on one end.
Do not solder within 6” (15.2 cm) from water inlet valve.
• 120°F (49°C) water at dishwasher.
• 3/8” O.D. copper tubing with compression fitting or flexible
stainless steel braided fill line (1/2” minimum plastic tubing is not
recommended).
• A 90° elbow with 3/8” N.P.T. external pipe threads on one end.
Do not solder within 6” (15.2 cm) from water inlet valve.
Electrical Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in conformance
with all national and local codes and ordinances.
You must have:
• 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply.
• Copper wire only.
We recommend:
• A time-delay fuse or circuit breaker.
• A separate circuit.
If direct wiring dishwasher:
• Use flexible, armored or non-metallic sheathed, copper wire with
grounding wire that meets the wiring requirements for your home
and local codes and ordinances.
• Use strain relief method provided with house wiring junction
box or install a U.L.-listed/CSA-certified clamp connector to the
house wiring junction box. If using conduit, use a U.L.-listed/CSA-
certified conduit connector.
If connecting dishwasher with a power supply cord:
• Use Power Supply Cord Kit (Part No. 4317824) marked for use
with dishwashers. Kit contents include:
– Volex, Inc., UL listed 16 gauge 3 wire power supply cord with 3
prong grounded plug.
– Neer C-500 7/8 inch strain relief.
– 3 wire connectors.
– Part No. 302797 grommet
Follow the kit instructions for installing the power supply cord.
• Power supply cord must plug into a mating three prong, grounded
outlet, located in the cabinet next to the dishwasher opening. Outlet
must meet all local codes and ordinances.
Assure that the electrical installation is adequate and in conformance
with all national and local codes and ordinances.
You must have:
• 120-volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical supply.
• Copper wire only.
We recommend:
• A time-delay fuse or circuit breaker.
• A separate circuit.
If direct wiring dishwasher:
• Use flexible, armored or non-metallic sheathed, copper wire with
grounding wire that meets the wiring requirements for your home
and local codes and ordinances.
• Use strain relief method provided with house wiring junction
box or install a U.L.-listed/CSA-certified clamp connector to the
house wiring junction box. If using conduit, use a U.L.-listed/CSA-
certified conduit connector.
If connecting dishwasher with a power supply cord:
• Use Power Supply Cord Kit (Part No. 4317824) marked for use
with dishwashers. Kit contents include:
– Volex, Inc., UL listed 16 gauge 3 wire power supply cord with 3
prong grounded plug.
– Neer C-500 7/8 inch strain relief.
– 3 wire connectors.
– Part No. 302797 grommet
Follow the kit instructions for installing the power supply cord.
• Power supply cord must plug into a mating three prong, grounded
outlet, located in the cabinet next to the dishwasher opening. Outlet
must meet all local codes and ordinances.
air gap