Mustang MV-PROJSP-FLAT-W Merkblatt

www.mustangav.com

MV-PROJSP-FLATW

Ceiling Projector Mount

The MV-PROJSP-FLAT-W spider mount provides

secure, versatile installation options for small to

medium sized projectors.

• Dimensions: 6” x 5” x 3”

• Weight capacity: up to 33 lbs (15 kg)

• Quick disconnection for simple maintenance

• One year warranty

• 1 Ceiling plate

• 1 U-bracket

• 1 General base plate

• 1 Cross adapter

• 1 Shaft

• 1 Locking hook

• 2 Extension brackets:   

  50 mm

• 2 Extension brackets:  

  75 mm

• 4 Truss head screws:  

  M4 x 15 mm

• 4 Truss head screws:  

  M4 x 20 mm

• 4 Truss head screws:  

  M4 x 25 mm

• 4 Truss head screws:  

  M4 x 30 mm

• 4 Truss head screws:  

  M5 x 15 mm

• 4 Truss head screws:  

  M5 x 20 mm

• 4 Truss head screws:  

  M5 x 25 mm

• 4 Truss head screws:  

  M5 x 30 mm

• 4 Truss head screws:  

  M6 x 15 mm

HARDWARE KIT

• 4 Truss head screws:  

  M6 x 20 mm

• 4 Truss head screws:  

  M6 x 25 mm

• 4 Truss head screws:  

  M6 x 30 mm

• 2 Socket cap screws:  

  M8 x 15 mm

• 7 Socket cap screws:  

  M8 x 50 mm

• 1 Socket cap screws:  

  M8 x 65 mm

• 8 Socket button cap  

  screws: M5 x 10 mm

• 7 M8 Self-locking  

  nylon nuts

• 1 M8nut

• 4 M8spring washers

• 4 Bottom spacers

• 8 Square nuts

• 2 Carriage bolts:  

  M6 x 12 mm

• 4 Washers: 1 mm

• 4 Washers: 2 mm

• 4 Washers: 4 mm

• 4 Washers: 8 mm

• 4 Washers: 16 mm

• 2 M6serrate flange nuts

Once you have located all of the hardware and 

components, you are ready to start installing the  

MV-PROJSP-FLATW.

1. Hold your projector carefully with both hands pointing  

    upwards on both sides of your projector.

2. Move your hands carefully alongside the projector   

    until it starts to tilt either upward or downward.

Note: this point is the central gravity point for the depth 

of your projector.

3. Hold your projector carefully with both hands on the  

    top and bottom sides of your projector pointing  

    towards the center of the projector.

4. Move your hands carefully along the projector until it  

    starts to tilt either upward or downward.

Note: this point is the central gravity point for the width 

of your projector.

5. Place a small piece of string (not supplied) around the  

    projector at the central gravity point of the depth of  

    your projector.

6. Place another small piece of string (not supplied)  

    around the projector at the central gravity point of the  

    width of your projector.

Note: where the two pieces of string meet is the central 

gravity point of your projector.

1. Determine the screw size needed to mount  

    your projector.

2. Place the pre-assembled universal base plate near the  

    central gravity point of your projector.

3. Select the appropriate extension bracket needed  

    for your installation.

4. Place the appropriate extension brackets near the  

    central gravity point of your projector.

Note: the extension brackets should all point toward the 

center of the universal base plate. Make sure they do not 

need to be forcibly attached to the base plate. If they do, 

you may need to change the size of extension

brackets for your installation.

5. Assemble each extension bracket with the  

   appropriately sized bottom spacer and other supplied   

   spacers (as required).

Note: if your extension bracket is more than 50 mm, 

you will also need to use two square nuts (which are 

supplied).

6. Assemble the universal base plate with the M6 nut,  

    U-joint bracket and M6 carriage bolts.

7. Align the assembled universal base plate with all of  

    the extension brackets already in place on your  

    projector.

8. Attach the universal base plate to the extension  

    brackets.

9. Install and tighten the M5 button socket cap screws and  

    the M6 serrate flange nuts to finish the assembly.

1. Install the ceiling plate to the ceiling with an M10  

    bolt (not included)

2. Connect the shaft with the bottom column.

3. Insert the locking hook into the cutting slot.

4. Tighten them with the M8 x 50 mm socket cap screw  

    and M8 self-locking nylon nuts.

Your MV-PROJSP-FLATW is now installed.

Note: The Only Difference Between The MV-PROJSP-

FLAT and the MV-PROJSP-FLATW is The Color. 

The MV-PROJSP-FLAT is Black and The MV-PROJSP-

FLATW is White.

MV-1.5ADAPTER - 1.5’’ NPT Adapter is available for 

PROJSP-FLATW. It works with MV-PROJSP series to 

convert your existing pipe to 1.5”.