Mustang MV-PROJSP-FLAT-W Dépliant
www.mustangav.com
MV-PROJSP-FLATW
Ceiling Projector Mount
The MV-PROJSP-FLAT-W spider mount provides
secure, versatile installation options for small to
medium sized projectors.
• Dimensions: 6” x 5” x 3”
• Weight capacity: up to 33 lbs (15 kg)
• Quick disconnection for simple maintenance
• One year warranty
• 1 Ceiling plate
• 1 U-bracket
• 1 General base plate
• 1 Cross adapter
• 1 Shaft
• 1 Locking hook
• 2 Extension brackets:
50 mm
• 2 Extension brackets:
75 mm
• 4 Truss head screws:
M4 x 15 mm
• 4 Truss head screws:
M4 x 20 mm
• 4 Truss head screws:
M4 x 25 mm
• 4 Truss head screws:
M4 x 30 mm
• 4 Truss head screws:
M5 x 15 mm
• 4 Truss head screws:
M5 x 20 mm
• 4 Truss head screws:
M5 x 25 mm
• 4 Truss head screws:
M5 x 30 mm
• 4 Truss head screws:
M6 x 15 mm
HARDWARE KIT
• 4 Truss head screws:
M6 x 20 mm
• 4 Truss head screws:
M6 x 25 mm
• 4 Truss head screws:
M6 x 30 mm
• 2 Socket cap screws:
M8 x 15 mm
• 7 Socket cap screws:
M8 x 50 mm
• 1 Socket cap screws:
M8 x 65 mm
• 8 Socket button cap
screws: M5 x 10 mm
• 7 M8 Self-locking
nylon nuts
• 1 M8nut
• 4 M8spring washers
• 4 Bottom spacers
• 8 Square nuts
• 2 Carriage bolts:
M6 x 12 mm
• 4 Washers: 1 mm
• 4 Washers: 2 mm
• 4 Washers: 4 mm
• 4 Washers: 8 mm
• 4 Washers: 16 mm
• 2 M6serrate flange nuts
Once you have located all of the hardware and
components, you are ready to start installing the
MV-PROJSP-FLATW.
Locate the central gravity of your projector
1. Hold your projector carefully with both hands pointing
upwards on both sides of your projector.
2. Move your hands carefully alongside the projector
until it starts to tilt either upward or downward.
Note: this point is the central gravity point for the depth
of your projector.
3. Hold your projector carefully with both hands on the
top and bottom sides of your projector pointing
towards the center of the projector.
4. Move your hands carefully along the projector until it
starts to tilt either upward or downward.
Note: this point is the central gravity point for the width
of your projector.
5. Place a small piece of string (not supplied) around the
projector at the central gravity point of the depth of
your projector.
6. Place another small piece of string (not supplied)
around the projector at the central gravity point of the
width of your projector.
Note: where the two pieces of string meet is the central
gravity point of your projector.
Install the universal base
1. Determine the screw size needed to mount
your projector.
2. Place the pre-assembled universal base plate near the
central gravity point of your projector.
3. Select the appropriate extension bracket needed
for your installation.
4. Place the appropriate extension brackets near the
central gravity point of your projector.
Note: the extension brackets should all point toward the
center of the universal base plate. Make sure they do not
need to be forcibly attached to the base plate. If they do,
you may need to change the size of extension
brackets for your installation.
5. Assemble each extension bracket with the
appropriately sized bottom spacer and other supplied
spacers (as required).
Note: if your extension bracket is more than 50 mm,
you will also need to use two square nuts (which are
supplied).
6. Assemble the universal base plate with the M6 nut,
U-joint bracket and M6 carriage bolts.
7. Align the assembled universal base plate with all of
the extension brackets already in place on your
projector.
8. Attach the universal base plate to the extension
brackets.
9. Install and tighten the M5 button socket cap screws and
the M6 serrate flange nuts to finish the assembly.
Install the MV-PROJSP-FLATW to the ceiling
1. Install the ceiling plate to the ceiling with an M10
bolt (not included)
2. Connect the shaft with the bottom column.
3. Insert the locking hook into the cutting slot.
4. Tighten them with the M8 x 50 mm socket cap screw
and M8 self-locking nylon nuts.
Your MV-PROJSP-FLATW is now installed.
Note: The Only Difference Between The MV-PROJSP-
FLAT and the MV-PROJSP-FLATW is The Color.
The MV-PROJSP-FLAT is Black and The MV-PROJSP-
FLATW is White.
MV-1.5ADAPTER - 1.5’’ NPT Adapter is available for
PROJSP-FLATW. It works with MV-PROJSP series to
convert your existing pipe to 1.5”.