Brother XR1300 Anleitung Für Quick Setup
1
Turn the power on.
2
Press the stitch category selection key
as many times as necessary until the
utility stitch indicator is lit.
as many times as necessary until the
utility stitch indicator is lit.
3
Press (stitch selection keys). The
number of the selected stitch is
displayed.
number of the selected stitch is
displayed.
4
Attach the presser foot indicated
in the LCD.
in the LCD.
1
Be sure to use the correct bobbin.
2
Press down on the spool pin lever.
Remove the spool cap.
Remove the spool cap.
3
Fully insert the spool of thread onto
the spool pin.
Slide the spool cap onto the spool pin.
the spool pin.
Slide the spool cap onto the spool pin.
4
1
Pass the thread under the thread
guide.
2
Pass the thread under the thread
guide cover.
3
Pull the thread to the right.
Make sure that the thread passes
under the pre-tension disk.
under the pre-tension disk.
5
Align the notch to the projection.
Slide the bobbin to the right.
Slide the bobbin to the right.
6
Wind the end of the thread.
Cut the thread.
Cut the thread.
7
Slide the sewing speed controller to
the right.
the right.
8
Turn the power on.
9
Press the foot controller or press
(start/stop button) to start.
(start/stop button) to start.
0
Winding starts. Wait until the bobbin
seems full and begins spinning slowly.
seems full and begins spinning slowly.
a
Take your foot off the foot controller or
press (start/stop button) to stop.
press (start/stop button) to stop.
b
Cut the thread.
Slide the bobbin to the left and remove
the bobbin from the shaft.
Slide the bobbin to the left and remove
the bobbin from the shaft.
c
Slide the sewing speed controller
to the left.
to the left.
d
Turn the power off.
e
Slide the button and open the cover.
f
Insert the bobbin.
Push the bobbin down.
Pull the thread firmly around the tab.
Cut the thread with the cutter.
Push the bobbin down.
Pull the thread firmly around the tab.
Cut the thread with the cutter.
g
Replace the bobbin cover.
11.5 mm
(7/16 inch)
(7/16 inch)
11,5 mm
(7/16 pulg.)
(7/16 pulg.)
1
1
3
2
4
2
3
4
5
8
6
7
9
0
a
b
d
f
e
g
■
Operation keys and LCD
Teclas de operación y pantalla de LCD
Teclas de operación y pantalla de LCD
■
Selecting a stitch
Selección de una puntada
Selección de una puntada
1
LCD (pantalla de cristal líquido)
1
Número de la puntada seleccionada
2
Pie prensatela que se va a utilizar
3
Longitud de la puntada (mm)
4
Anchura de la puntada (mm)
2
Teclas de selección de puntada
3
Tecla de ajuste de longitud de la puntada
4
Tecla de ajuste de anchura de la puntada
5
Indicador de puntada imagen en espejo
6
Indicador de puntada con aplicaciones
7
Tecla de selección de la categoría de puntada
8
Control de velocidad manual
9
Botón de Posición de aguja
0
Botón de Costura en reversa/remate
A
Botón de Inicio/parar
c
Example:
Ejemplo:
Ejemplo:
(04)
Refer to the Operation Manual for detailed instructions about sewing.
Consultar el manual de instrucciones detalladas acerca de la costura.
1
LCD (liquid crystal display)
1
Number of the selected stitch
2
Presser foot to be used
3
Stitch length (mm)
4
Stitch width (mm)
2
Stitch selection keys
3
Stitch length adjustment key
4
Stitch width adjustment key
5
Mirror image stitch indicator
6
Utility stitch indicator
7
Stitch category selection key
8
Sewing speed controller
9
Needle position button
0
Reverse/reinforcement stitch button
A
Start/stop button
8
9
0
0
A
7
5
6
3
4
2
1
1
2
1
1
2
3
2
3
2
2
1
3
1
Thread guide
Thread guide cover
Pre-tension disk
4
23
4
4
8d
560b
e
_
g
79ac
9a
Preparing the bobbin thread
Preparación del hilo de la bobina
Preparación del hilo de la bobina
PANTONE 2425
BLACK
Front