Alpine ina-n033r Benutzerhandbuch

-EN

Basic Operation

A/N DISP

MODE

Flipper switch

bass engine

Setting the Bass Control

You can change the Bass Frequency emphasis to create
your own tonal preference.

Press the bass engine button to change to the bass
engine mode.

Move the Flipper switch up or down to select BASS
CONT. Press the OK button or MODE knob to set the
BASS CONT. (Bass Center frequency control) mode.

3-1

Setting the bass Level:

Move the Flipper switch up or down to select BASS
LEVEL. Press the OK button or MODE knob to set.
Move the Flipper switch up or down to select the
desired bass level (–7~+7). Press the OK button or
Mode knob to set.
You can emphasize or weaken the bass frequency.

3-2

Setting the bass Centre frequency:

Move the Flipper switch up or down to select BASS
FREQ. Press the OK button or MODE knob to set.
Move the Flipper switch up or down to select the
desired bass centre frequency (60Hz ~ 180Hz). Press
the OK button or MODE knob to set.

Emphasizes the displayed Bass frequency ranges.

3-3

Setting the bass Band Width (Q-Factor):

Move the Flipper switch up or down to select BAND
WIDTH. Press the OK button or MODE knob to set.
Move the Flipper switch up or down to select the
desired bass Band Width (WIDE1 (Wide) ~ WIDE4
(Narrow)). Press the OK button or MODE knob to set.

Changes the bass boost band width to narrow or wide. A
wide setting will boost a wide range of frequencies above
and below the centre frequency. A narrower setting will
boost only frequencies near the centre frequency.

NOTES

• If no buttons are pressed within 10 seconds, the Bass control

setting will be turned off automatically.

• After 10 seconds from the completion of operation, the system

returns to the normal mode automatically. By pressing the
RTN button, the display returns to the previous indication.

Setting the Treble Control

You can change the Treble Frequency emphasis to
create your own tonal preference.

Press the bass engine button to change to the bass
engine mode.

Move the Flipper switch up or down to select TREBLE
CONT. Press the OK button or MODE knob to set the
TREBLE CONT. (Treble Center frequency control)
mode.

3-1

Setting the treble Level:

Move the Flipper switch up or down to select TREBLE
LEVEL. Press the OK button to set.
Move the Flipper switch up or down to select the
desired Treble level (–7~+7). Press the OK button or
MODE knob to set.
You can emphasize the treble frequency.

3-2

Setting the treble Centre frequency:

Move the Flipper switch up or down to select TREBLE
FREQ. Press the OK button to set.
Move the Flipper switch up or down to select the
desired treble centre frequency (10.0kHz ~ 17.5kHz).
Press the OK button or MODE knob to set.

Emphasizes the displayed Treble frequency ranges.

NOTES

• If no buttons are pressed within 10 seconds, the Treble control

setting will be turned off automatically.

• After 10 seconds from the operation is completed, the system

returns to the normal mode automatically. By pressing the
RTN button, the display returns to the previous setting
indication.

Automatic Position Display

Press the A/N DISP button to change the display.
Automatic position (present position) and the GPS
receiving sensitivity are displayed.

NOTES

• To display the present position of your vehicle, connect the

GPS antenna to the unit. (refer to “Installing the GPS
Antenna” on page 26.).

• When inserting the separately sold navigation disk (NVD-

T001) specialized for this unit, navigating operations from the
unit become available. MENU and VOICE button are used for
navigating operations.
You cannot use the info button at present. It will be used for
functions to be added in the future (e.g. traffic information
reception, etc.). (Except some areas.)

Example of vehicle’s present position

•

The GPS receiving sensitivity and the
number of satellites are displayed.