TEAC quick 552e Benutzerhandbuch
Drive Installation Directions
The drive is operated in horizontal position. The eject
button is located on the right side of the panel. Installa-
tion position is not allowed to be tilted more than 15
degrees out of the horizontal position.
button is located on the right side of the panel. Installa-
tion position is not allowed to be tilted more than 15
degrees out of the horizontal position.
Jumpers for IDE Configuration
The strap is factory-preset as shown:
The TEAC CD-552E can be operated in the modes
Cable Select (CS), Master (MA) or Slave (SL).
Cable Select (CS), Master (MA) or Slave (SL).
Important:
During setting the mode be sure to switch off
respectively disconnect any voltages con-
nected to the drive (see section “Installation
and Connection”).
respectively disconnect any voltages con-
nected to the drive (see section “Installation
and Connection”).
TEAC CD-552E CD-ROM Drive
Quick Installation Guide
page 1
Remarks:
X: jumper set
–: jumper not set (left open)
–: jumper not set (left open)
Installation and Connection
Note:
To use the TEAC CD-ROM drive an IDE
(ATAPI) controller is required. Usually it is in-
tegrated on the system board of your PC. The
drivers required for operating the CD-ROM
drive are a part of your operating system.
(ATAPI) controller is required. Usually it is in-
tegrated on the system board of your PC. The
drivers required for operating the CD-ROM
drive are a part of your operating system.
Very important:
Switch off your PC and any attached devices
and disconnect the power cord(s). It is not
sufficent to switch off the power switch! Do
the same if the CD-ROM drive is reconfigured.
and disconnect the power cord(s). It is not
sufficent to switch off the power switch! Do
the same if the CD-ROM drive is reconfigured.
(1)
Open the case of your PC and lift it off carefully.
(2)
Configure the CD-ROM drive if neccessary.
(3)
Locate a free slot for 5.25” drives and install the
drive using the provided four screws.
drive using the provided four screws.
(4)
Connect the power cable and the 40-pin data cable
(assure the correct orientation, pin 1 is often
marked with a color stripe) to the drive. Connect-
ing in the wrong orientation may damage the drive
and the PC!
(assure the correct orientation, pin 1 is often
marked with a color stripe) to the drive. Connect-
ing in the wrong orientation may damage the drive
and the PC!
Power cable
40-pin IDE
data cable
data cable
Audio cable
Pin 1
CD-552E
(5)
Connect the provided audio cable to the sound
card.
card.
Usually sound cards offer more than one connec-
tor to connect an audio cable to. Please refer to
the manual of the sound card to find the connec-
tor in question.
tor to connect an audio cable to. Please refer to
the manual of the sound card to find the connec-
tor in question.
(6)
Close the case of the PC. Do not forget to connect
other devices and accessories if there are any.
other devices and accessories if there are any.
C
S
S
S
L
M
A
A
Remarks
–
–
X
Master: CD-ROM drive is configured as first IDE
drive (basic setting).
This configuration can be used only if the drive is
connected to the second IDE controller
This configuration can be used only if the drive is
connected to the second IDE controller
(secondary IDE). If a hard disk is already operated
at the secondary IDE controller (configured as
master) the jumper setting at the CD-ROM has to
be changed to slave.
master) the jumper setting at the CD-ROM has to
be changed to slave.
–
X
–
Slave: CD-ROM drive is configured as second IDE
drive.
drive.
If there is only one hard disk in the PC the CD-
ROM can be operated at the same IDE connection
parallel to this hard disk. Important: The data rates
ROM can be operated at the same IDE connection
parallel to this hard disk. Important: The data rates
of both devices may be decreased.
X
–
–
Cable Select: Master/slave detection is achieved
by the controller.
by the controller.
S
L
L
M
A
A
C
S
S
Digital audio
output connector
output connector
Analog audio
output connector
output connector
40-pin IDE flat cable
connector
Power connector
Pin 1