ICOM ic-m801gmdss Benutzerhandbuch
6
14
FREQUENCY PROGRAMMING
■ Frequency selection
D
D Using the channel selector
q Select a channel which is programmed near the
frequency you want to receive.
w Push [RX
CLAR
] to select the frequency selection
mode.
• “
≈” appears in the display.
e Rotate [GRP] to select the digit for tuning.
• Under-bar shows the selected digit.
r Rotate [CH] to tune the frequency.
• Pushing [Y]/[Z] on the microphone also tunes the fre-
quency.
t Repeat steps e and r to complete the frequency
selection.
y To return to the previous frequency, push
[RX
CLAR
].
• “
≈” disappears.
0 1 2 3 4 A
C H
- - - G P S - - -
L a t 4 5 5 9 ' N
L o n 1 3 4 4 4 ' E
1 6 : 2 3
R X
J 3 E
S I M P
Ç
The under-bar is moved by rotating
[GRP].
[GRP].
0 1 2 3 4 A
C H
- - - G P S - - -
L a t 4 5 5 9 ' N
L o n 1 3 4 4 4 ' E
1 6 : 2 3
R X
J 3 E
S I M P
Ç
“Ç” and frequency show that the
frequency can be changed.
frequency can be changed.
D
D Using the keypad
CAUTION: A frequency can be programmed into a
user or e-mail channel by pushing and holding
[ENT] for 1 sec. after entering a frequency. An ITU
simplex frequency can only be programmed on a
temporary basis. Keypad entry should be used only
on spare (or blank) channels.
user or e-mail channel by pushing and holding
[ENT] for 1 sec. after entering a frequency. An ITU
simplex frequency can only be programmed on a
temporary basis. Keypad entry should be used only
on spare (or blank) channels.
q Rotate [GRP] and [CH], or enter a 1 to 4 digit num-
ber via the keypad, then push [ENT] to select the
memory channel to be used for general coverage
use.
memory channel to be used for general coverage
use.
When a blank channel is selected, operating frequency,
mode and channel name do not appear.
mode and channel name do not appear.
w Push [RX
CLAR
] to select the frequency selection
mode.
• “
≈” appears in the display.
e Enter 4 to 6 digits of the desired frequency via the
keypad.
r Push [ENT] momentarily to input the frequency.
• DO NOT hold [ENT] for more than 1 sec., otherwise the
frequency will be programmed into the channel.
[EXAMPLE]: Setting 12.3450 MHz
• The set frequency can be cleared when [RX
CLAR
] is
pushed while setting.
Ç
Ç
Ç
Ç
0 1 2 3 4 A
C H
- - - G P S - - -
L a t 4 5 5 9 ' N
L o n 1 3 4 4 4 ' E
1 6 : 2 3
R X
J 3 E
S I M P
Ç
Select blank channel.
Push [RX
CLAR
]
[1
NB
]
[2
SQL
], [3
SCAN
],
[4
SP
×
], [5
AGC
×
]
[0
DIM
]
[ENT]
0 1 2 3 4 A
C H
- - - G P S - - -
L a t 4 5 5 9 ' N
L o n 1 3 4 4 4 ' E
1 6 : 2 3