Juniper Networks T1600 Benutzerhandbuch
■
Multiprotocol Label Switching (MPLS) circuit cross-connect for leveraging ATM access
networks
networks
■
User-configurable virtual circuit (VC) and virtual path (VP) support
■
Support for idle cell or unassigned cell transmission
■
OAM Fault Management processes Alarm Indication Signal (AIS), Remote Defect Indicator
(RDI), and loop cells
(RDI), and loop cells
■
Point-to-point and point-to-multipoint mode Layer 2 counters per VC and per VP
■
Local and remote loopback
■
ATM Inverse ARP, which enables routers to automatically learn the IP address of the
router on the far end of an ATM PVC
router on the far end of an ATM PVC
■
Simple Network Management Protocol (SNMP):
■
Management Information Base (MIB) 2 (RFC 1213)
■
ATM MIB (RFC 1695)
■
SONET MIB
■
Unspecified bit rate (UBR), non-real-time variable bit rate (VBR), and constant bit rate
(CBR) traffic shaping
(CBR) traffic shaping
■
Per-VC or per-VP traffic shaping
■
Support for F4 OAM cells
■
Support for 16-bit VCI range
Software features
■
You can install different transceivers on the PIC. For information about installing and
removing transceivers, see the PIC and Transceiver Installation Instructions.
removing transceivers, see the PIC and Transceiver Installation Instructions.
■
Duplex SC/PC connector (RX and TX)
■
Optical interface support—see Table 17 on page 27
Cables and connectors
One tricolor per port:
■
Off—Not enabled
■
Green—Online with no alarms or failures
■
Amber—Online with alarms for remote failures
■
Red—Active with a local alarm; router has detected a failure
LEDs
■
Alarm indication signal (AIS-L, AIS-P)
■
Bit error rate signal degrade (BERR-SD), bit error rate signal fail (BERR-SF)
■
Bit interleaved parity errors B1, B2, B3
■
Errored seconds (ES-S, ES-L, ES-P), far-end bit errors REI-L, REI-P (CV-LFE, CV-PFE),
far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE,
SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PFE)
far-end errored seconds (ES-LFE, ES-PFE), far-end severely errored seconds (SES-LFE,
SES-PFE), far-end unavailable seconds (UAS-LFE, UAS-PFE)
■
Loss of cell delineation (LOC), loss of frame (LOF), loss of pointer (LOP-P), loss of signal
(LOS)
(LOS)
■
Payload mismatch (PLM-P), payload unequipped (UNEQ-P)
■
Remote defect indication (RDI-L, RDI-P)
■
Severely errored framing (SEF), severely errored framing seconds (SEFS-S), severely
errored seconds (SES-S, SES-L, SES-P), unavailable seconds (UAS-L, UAS-P)
errored seconds (SES-S, SES-L, SES-P), unavailable seconds (UAS-L, UAS-P)
Alarms, errors, and
events
events
Table 17: Optical Interface Support for ATM2 OC48/STM16 IQ PICs
Multimode
Intermediate Reach (IR)
Optical Parameter
Multimode
Single-mode
Optical interface
ATM2 OC48/STM16 IQ PIC with SFP
■
27
ATM2 OC48/STM16 IQ PIC with SFP