multicoat kretekoter Benutzerhandbuch

With Hopper Gun - Trowel Knock Down to achieve French

Lace Texture.

ACRATHANE COLORSEAL must be applied in two thin coats.

First Coat - Mix Colorseal to uniformity with slow speed
mixer. With continuous mixing, add clean water in ratio of

1 part water to 3 parts Colorseal. APPLY DILUTED COL-

ORSEAL WITH

” TO

” nap roller, using firm pressure.

Allow a minimum of (1) hour to dry.

(Note: ACRATHANE Clear Sealers are applied in one or
two coats full strength. DO NOT DILUTE.)

Second Coat - DO NOT DILUTE COLORSEAL! Mix to unifor-
mity only. Apply with firm pressure. DO NOT APPLY THICKER

THAN RECOMMENDED! Airless sprayer may be used for

final coat.

Allow to cure for a minimum of 24-48 hours before commenc-

ing foot traffic, 48-72 hours for vehicular traffic.

COVERAGE

Each 65 lb. of KRETE KOTE or TOP COAT 2000 as described

under “APPLICATION,” will cover approximately 100 sq. ft. (2

coats) or 65 sq.ft. (3 coats). Each gallon of ACRATHANE

COLORSEAL will cover approximately 150-200 sq. ft. per

gallon, depending on surface texture and/porosity. (See

ACRATHANE COLORSEAL Instructions for use).

LIMITATIONS

Do not apply when substrate surface temperature is below

50°F, above 100°F if ambient temperature is below 50°F and

falling, over 100°F and expected to rise, or if precipitation is

expected within a 24 hour period.

DO NOT USE IF CONCRETE SLAB MAY BE SUBJECT TO
NEGATIVE SIDE WATER OR WATER VAPOR PRESSURE.

Do not bridge expansion or control joints with the Krete
Kote System. All expansion or control joints must be cut
and cleaned out and filled with approved caulking material.

PACKAGING AND STORAGE

KRETE KOTE or TOP COAT 2000 are furnished in 65 lb bags.

ACRATHANE COLORSEAL is furnished in 1 and 5 gallon

containers.

Store in dry area at 40°-90°F.

Shelf life is approximately 24 months in unopened bags and

approximately 18 months in unopened pails.

WARRANTY

Materials are guaranteed with respect to uniformity and quality

within manufacturers' specifications. Seller makes no other

warranty, expressed or implied, regarding the use of its products.

Since use of the product is beyond the Seller's control, the Buyer

assumes all risks of use. Seller's sole obligation shall be to replace

material if found to be defective. Seller shall not be liable for any

damages, injury, loss, direct or indirect or consequential, resulting

from use of its products.

Limited warranty available to experienced MULTICOAT Certified

Applicators.

TEST DATA — KRETE KOTE 2000 / TOP COAT 2000

TEST

METHOD

RESULTS

1. Weatherometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM G23 . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 hrs - Passed

2. Compressive Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM C109 . . . . . 45 Days air cured . . . . . . . . . . . . . 2595 psi

3. Tensile Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-C190 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457 psi

4. Bond Strength (Flatwise Tension) . . . . . . . . . . . . . . . . . . . . . . .ASTM-C297 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225 psi

5. Abrasion Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-1242A . . . . 1000cyc-1000gms . . . . . . . . . . . 39 mil loss

6. Salt Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-B117 . . . . . . . . . . . . . . . . . . . . . . . . . . . 300 hrs - Passed

7. Water Vapor Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-E96A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.26 Perms

8. 50-Cycle Freeze thaw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-C67 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passed

9. Flexural Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-D790 . . . . . . . . . . . . . . . . . . Modulus of Rupture - 770psi

10. Impact Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MIL-D-3134F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Passed

11. Flame Spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .ASTM-E84 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class A

The Coating of the Future…Today

MC0406

MULTICOAT

CORPORATION

West Coast

Toll Free: (877) 685-8426
(949) 888-7100 Fax (949) 888-2555
Website: www.multicoat.com
E-mail: info@multicoat.com

MULTICOAT

PRODUCTS, INC.

East Coast

Toll Free: (800) 660-6729
(304) 586-0616 Fax (304) 586-0620
Website: www.multicoat.com
E-mail: info@multicoat.com

Available Through: