multicoat slatexabover Benutzerhandbuch

Coat all plywood joints, flashings, posts, drains, coves, stairwells

and other irregularities with MULASTICOAT; embed with

Stitchbonded Polyester Fabric; apply additional MULASTICOAT to

saturate fabric, and allow to dry. MULASTICOAT is then applied

over entire substrate in two (2) coats with roller, using firm pres-

sure. (See "COVERAGE" below.)

First coat is allowed to dry to touch, usually 1-2 hours depending

on ambient temperature. Second coat is applied crisscross to first

coat. Allow MULASTICOAT to fully dry before proceeding with

KRETE KOTE/TOP COAT 2000 surfacing.  DO NOT ALLOW

MULASTICOAT TO BE EXPOSED FOR MORE THAN 3 DAYS.

Before proceeding, remove dust from MULASTICOAT with damp

sponge.

First coat of KRETE KOTE/TOP COAT 2000 (see KRETE KOTE

2000 instructions for mixing information) is applied with roller,

squeegee or trowel; fiberglass mesh is immediately embedded

and troweled down firmly. Minimum 2 hours initial cure, longer in

cool weather.

Second coat of KRETE KOTE/TOP COAT 2000 is applied firmly

with trowel. Minimum 2 hours cure time, longer in cool weather. 

Third coat is applied with trowel or hopper gun, depending upon

whether smooth or textured finish is desired. Allow to cure a

minimum of twelve (12) hours before allowing foot traffic and

seventy-two (72) hours minimum for vehicular traffic, longer in 

cool weather.

Not responsible for cracks and delamination caused by
structural movement, improper substrate or application - 
SEE WARRANTY.

(Recommended)

Apply two coats of COLORSEAL (Refer to COLORSEAL

“Instructions for use.”) Allow minimum 24 hour cure before allowing
foot traffic and minimum 72 hours before allowing vehicle traffic.

MULASTICOAT (waterproofing membrane): 40 to 50 sq. ft. per
gallon (2 coats).

KRETE KOTE/TOP COAT 2000 - 65 sq. ft. per bag (3 coats).

(See "PACKAGING AND STORAGE")

COLORSEAL 150 - 200 sq. ft. per gallon (2 coats).

Do not apply any components of the SLATEX SYSTEM when sub-
strate surface temperature is below 50°F, above 100°F, if ambient
temperature is below 50°F and falling, over 100°F and expected to
rise, or if precipitation is expected within a 24 hour period.

MULASTICOAT - furnished in 1 and 5 gallon containers, 55 gallon
drums and 275 gallon totes.

KRETE KOTE/TOP COAT 2000 - furnished in 65 lb. bags.

COLORSEAL - furnished in 1 and 5 gallon pails.

Fiberglass Mesh - 475 sq. ft. rolls.

Stitchbonded Plyester Fabric - 10” wide rolls x 324 ft. long.

Store at 40-90°F in Dry Area.

Shelf life is approximately 24 months in unopened bags and
approximately 18 months in unopened pails.

Materials are guaranteed with respect to uniformity and quality within
manufacturers’ specifications. Seller makes no other warranty,
expressed or implied, regarding the use of its products. Since use of
the product is beyond Seller’s control, the Buyer assumes all risks of
use. Seller’s sole obligation shall be to replace material if found to be
defective. Seller shall not be liable for any damages, injury, loss, direct
or consequential, resulting from use of its products.

1. Weatherometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM G23 

2000 Hrs. 

Passed

2. Aging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM A756D & E

25 Cycles

Passed

3. Bond Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM C297 

P

LYWOOD

C

ONCRETE

Before Aging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

91 psi

209 psi

After Aging  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM A756D & E

89 psi

218 psi

Failure at: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Plywood

Mulasticoat

4. Abrasion Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM D-1242A

1000Rev - 1000Gm Load 

39 mil Loss

5. Percolation Tests  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2” Dia x 48” Water head for 48 Hrs

No Loss

6. Absorption Tests  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM D570

Water Absorption 8.1%

7. Chemical Resistance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM D2299

To most Chemicals and Solvents

8. Freeze Thaw 50 Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ASTM C67

P

LYWOOD

C

ONCRETE

Bond Strength  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

91 psi

202 psi

Failure at: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Plywood

Mulasticoat

9. Concentrated Load Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 Ib., 5 Cycles

Load Deflection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

.031 in.

Residual Indentation - Final . . . . . . . . . . . . . . . . . . . . . . . . . 

.

018 in.

10. Fire Retardant Roof Test  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UBC 32-7)

Class B

11. Anti-Skid Test (Leather and Rubber)  . . . . . . . . . . . . . . . . . . . . ASTM C1028

D

RY

W

ET

Factor of Static Friction. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

.87 - .88

.75 - .79

Factor of Sliding Friction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 

.52 - .77

.67 - .72

12. Wind Uplift Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Factory Mutual 1-52

Passed

MC0406

Toll Free: (877) 685-8426
(949) 888-7100  Fax (949) 888-2555
Website: www.multicoat.com
E-mail: info@multicoat.com

Toll Free: (800) 660-6729
(304) 586-0616  Fax (304) 586-0620
Website: www.multicoat.com
E-mail: info@multicoat.com