multicoat crackrepair Benutzerhandbuch

Do not apply when substrate surface temperature is below 50°F,

above 100°F, if ambient temperature is below 50°F or over 100°F

and expected to rise, or if precipitation is expected within a 6

hour period.

SPEED BOND is furnished in a 12 oz. cartridge.

Store in a dry place at 65° to 85° (18° to 30°C).

Note: A special caulking gun needs to be purchased to properly

dispense SPEED BOND. Caulking guns are readily available

through Multicoat or your local Multicoat Distributor.

Materials are guaranteed with respect to uniformity and quality

within manufacturers’ specifications. Seller makes no other 

warranty, expressed or implied, regarding the use of its products.

Since use of the product is beyond the Seller’s control, the Buyer

assumes all risks of use. Seller's sole obligation shall be to

replace material if found to be defective. Seller shall not be liable

for any damages, injury, loss, direct or indirect or consequential,

resulting from use of its products.

1. Appearance  . . . . . . . . . . . . . . . . . . .Cured . . . . . . . . . . . . . . . . . . MC . . . . . . . . . . . . . . . . . Grey

2. Viscosity Pt. A  . . . . . . . . . . . . . . . . . .25° C . . . . . . . . . . . . . . . . . . Brookfield HBDVI CP . . . 4050 cps

3. Viscosity Pt. B  . . . . . . . . . . . . . . . . . .25° C . . . . . . . . . . . . . . . . . . Brookfield HBDVI CP . . . 2500 cps

4. Work Life . . . . . . . . . . . . . . . . . . . . . .10g 

1

⁄

4

" Thick @ 25° C . . . . . . MC . . . . . . . . . . . . . . . . . 70 seconds

5. Tack-Free Time  . . . . . . . . . . . . . . . . .10g 

1

⁄

4

" Thick @ 25° C . . . . . . MC . . . . . . . . . . . . . . . . . 4 minutes

6. Full Cure Time . . . . . . . . . . . . . . . . . .10g 

1

⁄

4

" Thick @ 25° C . . . . . . MC . . . . . . . . . . . . . . . . . 1 hour

7. Hardness  . . . . . . . . . . . . . . . . . . . . .1 hour @ 25° C . . . . . . . . . . . ASTM D2240-91 . . . . . . . 70 Shore D

8. Lap Sheer on Etched Aluminum . . . .7 days @ 25° C. . . . . . . . . . . ASTM D1002-72 . . . . . . . 14.8 N/mm2 (2150 psi)

9. Tensil Strength  . . . . . . . . . . . . . . . . .7 days @ 25° C. . . . . . . . . . . ASTM D638-91 . . . . . . . . 33.7 N/mm (4900 psi)

10. Elongation . . . . . . . . . . . . . . . . . . . . .7 days @ 25° C. . . . . . . . . . . ASTM D638-91 . . . . . . . . 48%

11. Coefficient of Linear  . . . . . . . . . . . . .62° C to 167° C . . . . . . . . . . DuPont 943 TMA. . . . . . . 200 um/m°c

12. Thermal Expansion  . . . . . . . . . . . . . .-82° C to +30° C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 um/m°c

13. Glass Transition Temperature (TG)  . . .Fully Cured . . . . . . . . . . . . . . Dupont 943 TMA. . . . . . . 40° C

14. Temperature Range  . . . . . . . . . . . . .Continuous . . . . . . . . . . . . . . MC . . . . . . . . . . . . . . . . . -40° to 121° C

MC1004

Toll Free: (877) MULTICO (685-8426)
(949) 888-7100  FAX (949) 888-2555
website: www.multicoat.com
E-mail: multi5000@aol.com

Toll Free: (800) 660-6729 or (304) 768-0017
FAX (304) 768-9738
website: www.multicoatproducts.com
E-mail: multiprods@aol.com