Panasonic VDRM75EB Bedienungsanleitung
44
Inserting and Removing Disc
Inserting Disc
1
Press the DISC EJECT lever down once and
release it.
release it.
A few moments after the ACCESS/PC indicator
blinks, the cover of disc insertion block will open
slightly.
blinks, the cover of disc insertion block will open
slightly.
2
Open the cover by hand and fit the disc onto the
spindle in the centre.
spindle in the centre.
Note
:
•
The exposed disc portion must face in the same
direction as the lens, as shown in figure.
direction as the lens, as shown in figure.
•
The recording/playback side must face the inside
(DVD Video Camera).
(DVD Video Camera).
•
Do not use excessive force when opening the
cover.
cover.
•
Do not touch the pickup lens or the recording/
playback side of the disc.
This may impair recording and playback.
playback side of the disc.
This may impair recording and playback.
•
Insert the disc securely to prevent damage.
•
When you open the lid, the ACCESS/PC indicator
flashes red. Do not leave the lid open.
flashes red. Do not leave the lid open.
3
Push the section marked “PUSH CLOSE” on
the cover of disc insertion block, to close the
cover.
the cover of disc insertion block, to close the
cover.
4
Turn the DVD Video Camera on (
or
).
When “DISC ACCESS” disappears, the DVD
Video Camera is ready for recording.
Video Camera is ready for recording.
Note
:
Immediately after a disc is inserted or recording is finished:
If the ACCESS/PC indicator is lit or blinking immediately
after a disc is inserted or recording is finished, then the disc
is spinning and disc information is being saved. If the power
supply is cut off while this is happening, the disc may
become unusable. For this reason, the power cord must not
be unplugged and the battery must not be removed when
the ACCESS/PC indicator is lit or blinking immediately after
a disc is inserted.
While the ACCESS/PC or CARD ACCESS indicator is lit or
blinking, do not cause impact or vibration to the DVD Video
Camera.
If the ACCESS/PC indicator is lit or blinking immediately
after a disc is inserted or recording is finished, then the disc
is spinning and disc information is being saved. If the power
supply is cut off while this is happening, the disc may
become unusable. For this reason, the power cord must not
be unplugged and the battery must not be removed when
the ACCESS/PC indicator is lit or blinking immediately after
a disc is inserted.
While the ACCESS/PC or CARD ACCESS indicator is lit or
blinking, do not cause impact or vibration to the DVD Video
Camera.
zIdentifying recording/playback
sides of disc:
This section describes double-
sided discs. Note that the included
DVD-RAM disc is a single-sided
disc.
sided discs. Note that the included
DVD-RAM disc is a single-sided
disc.
Single sided disc:
The recording/playback side is
opposite to the labelled side.
Double-sided disc:
The “SIDE A” recording/
playback side is opposite to the
“SIDE A” marked side.
The “SIDE B” recording/
playback side is the “SIDE A”
marked side.
The recording/playback side is
opposite to the labelled side.
Double-sided disc:
The “SIDE A” recording/
playback side is opposite to the
“SIDE A” marked side.
The “SIDE B” recording/
playback side is the “SIDE A”
marked side.
Recording/
playback side
playback side
DISC EJECT
lever
lever
Pickup lens
Push the shaded
portion.
portion.
ACCESS/PC
indicator
indicator
DV
D-R
AM / SIDE
A
The opposite
side is the “SIDE
A” recording/
playback side.
side is the “SIDE
A” recording/
playback side.
“SIDE A” mark
VDR-M75M55EB.book Page 44 Tuesday, May 17, 2005 10:32 AM