Moxa ioLogik E2212 IOLOGIK E2212 Benutzerhandbuch
Produktcode
IOLOGIK E2212
1
w w w. m o x a . c o m
i n f o @ m o x a . c o m
Automation Controllers
ioLogik E2212
Front-end intelligence that supports 24 Click&Go™ rules
›
Active Messaging with real-time stamp, including SMS,
›
SNMP Trap with I/O status, TCP, and email
Supports SNMPv1/v2c/v3 protocol
›
I/O peer-to-peer function
›
Built-in web console
›
PC utility: Auto detection of installed modules
›
Windows/WinCE VB/VC.NET and Linux C APIs
›
Moxa’s ioLogik E2212 is a new type of active micro controller that
can be used as an RTU (Remote Terminal Unit). Active Ethernet micro
controllers are a kind of PC-based data acquisition and control device
that use proactive, event-based reporting to control I/O devices. Unlike
traditional RTUs, which are passive and must poll for data, Moxa’s
Active OPC Server makes seamless connection with SCADA systems
can be used as an RTU (Remote Terminal Unit). Active Ethernet micro
controllers are a kind of PC-based data acquisition and control device
that use proactive, event-based reporting to control I/O devices. Unlike
traditional RTUs, which are passive and must poll for data, Moxa’s
Active OPC Server makes seamless connection with SCADA systems
a reality. In addition, SNMP is used for communicating with an NMS
(Network Management System) for IT field users. The I/O status of
an Active Ethernet micro controller can be reported and controlled
automatically on-site based on user specified conditions. This report-
by-exception approach, which is new to PC-based monitoring, requires
far less bandwidth than traditional polling methods.
(Network Management System) for IT field users. The I/O status of
an Active Ethernet micro controller can be reported and controlled
automatically on-site based on user specified conditions. This report-
by-exception approach, which is new to PC-based monitoring, requires
far less bandwidth than traditional polling methods.
Active Ethernet micro controller with 8 digital inputs,
8 digital outputs, and 4 DIOs
Introduction
LAN
Ethernet: 1 x 10/100 Mbps, RJ45
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP,
CGI, SNTP
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP, HTTP,
CGI, SNTP
Serial Communication
Interface: RS-485-2w: Data+, Data-, GND
Serial Line Protection: 15 KV ESD for all signals
Serial Line Protection: 15 KV ESD for all signals
Serial Communication Parameters
Parity: None
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
Digital Input
Channels: 8, source/sink selectable
Sensor Type: NPN, PNP, and Dry contact
I/O Mode: DI or Event Counter (up to 900 Hz)
Dry Contact:
• Logic 0: short to GND
• Logic 1: open
Wet Contact:
Sensor Type: NPN, PNP, and Dry contact
I/O Mode: DI or Event Counter (up to 900 Hz)
Dry Contact:
• Logic 0: short to GND
• Logic 1: open
Wet Contact:
Common Type: 6 points per COM
Isolation: 3K VDC or 2K Vrms
Counter/Frequency: 900 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Over-voltage Protection: 36 VDC
Poweroff Counter: Supports poweroff counter storage function
Isolation: 3K VDC or 2K Vrms
Counter/Frequency: 900 Hz, power off storage
Digital Filtering Time Interval: Software selectable
Over-voltage Protection: 36 VDC
Poweroff Counter: Supports poweroff counter storage function
Digital Output
Channels: 8, sink type, 36 VDC, 200 mA
I/O Mode: DO or Pulse Output (up to 100 Hz)
Pulse Wave Width/Frequency: 10 ms/100 Hz
Over-voltage Protection: 45 VDC
Over-current Limit: 400 mA (typical)
Over-temperature Shutdown: 175°C (min.)
Output Current Rating: Max. 200 mA per channel
Isolation: 2K Vrms or 3K VDC (Magnetic)
I/O Mode: DO or Pulse Output (up to 100 Hz)
Pulse Wave Width/Frequency: 10 ms/100 Hz
Over-voltage Protection: 45 VDC
Over-current Limit: 400 mA (typical)
Over-temperature Shutdown: 175°C (min.)
Output Current Rating: Max. 200 mA per channel
Isolation: 2K Vrms or 3K VDC (Magnetic)
DI/DO Configurable Channels
Channels: 4
I/O Mode:
• DI or Event Counter (up to 900 Hz)
• DO or Pulse Output (up to 100 Hz)
I/O Mode:
• DI or Event Counter (up to 900 Hz)
• DO or Pulse Output (up to 100 Hz)
Power Requirements
Power Input: 24 VDC nominal, 12 to 36 VDC
Power Consumption: 282 mA typical @ 24 VDC
Power Consumption: 282 mA typical @ 24 VDC
Physical Characteristics
Wiring: I/O cable max. 14 AWG
Dimensions: 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight: under 250 g
Dimensions: 115 x 79 x 45.6 mm (4.53 x 3.11 x 1.80 in)
Weight: under 250 g
DI Type
Status
Source
Sink
ON
0 to 3 VDC
10 to 30 VDC
OFF
10 to 30 VDC
0 to 3 VDC
Specifications