Ruckus Wireless R600 Benutzerhandbuch
Copyright © 2014 Ruckus Wireless, Inc.
Page 1 of 4
Published September 2014, Part Number 800-70633-001 Rev B
R600 Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions
on how to set up your Ruckus Wireless R600 Dual Band
802.11ac Multimedia Wi-Fi Access Point. After completing
the steps described in this Guide, you will be able to place
the Access Point (AP) at your site and provide wireless
network access to users.
on how to set up your Ruckus Wireless R600 Dual Band
802.11ac Multimedia Wi-Fi Access Point. After completing
the steps described in this Guide, you will be able to place
the Access Point (AP) at your site and provide wireless
network access to users.
T
HIS
G
UIDE
IN
O
THER
L
ANGUAGES
•
请从以下网站获得该指南的简体中文版
.
•
Vous trouverez la version française de ce guide à l'adresse
suivante
suivante
.
•
で ご覧 く だ さ い。
•
이 가이드의 한국어 버전은 웹 사이트
(
(
) 에서 확인하시기 바
랍니다 .
•
Veja a versão em português (Brasil) deste guia em
•
Puede ver la versión en español (América Latina) de esta
guía en
guía en
B
EFORE
Y
OU
B
EGIN
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
the latest software and the release documentation.
•
User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents
.
•
Software Upgrades are available at
http://support.ruckuswireless.com/software
.
•
Open Source information is available at
http://opensource.ruckuswireless.com
.
•
Software License and Limited Warranty are available at
http://support.ruckuswireless.com/warranty
.
P
ACKAGE
C
ONTENTS
•
R600 Access Point
•
One wall-mount anchor kit, including two 1" No. 8 steel pan-
head Phillips sheet metal screws, one 5mm M2.5 x 1.06 Torx
security screw, and wall-mount anchors
head Phillips sheet metal screws, one 5mm M2.5 x 1.06 Torx
security screw, and wall-mount anchors
•
One external T-bar bracket (two unassembled parts)
•
One unit removal pin
•
Regulatory flyer
•
Product warranty statement
•
Declaration of Conformity, if required
•
This Quick Setup Guide
S
TEP
1: C
OLLECT
T
OOLS
AND
S
ETUP
R
EQUIRE
-
MENTS
•
A computer running Windows 7 (procedures for other OS’s
are similar)
are similar)
•
Two Cat 5e Ethernet cables
•
No. 2 Phillips screwdriver and T8 Torx driver for wall mount-
ing anchor kit
ing anchor kit
•
An AC power adapter (sold separately), or
an 802.3af- or 802.3at-compliant Power over Ethernet
(PoE) switch or PoE injector
(PoE) switch or PoE injector
•
When mounting the R600 to a truss or pole, two customer-
supplied cable ties
supplied cable ties
S
TEP
2: C
ONNECT
THE
AP
TO
Y
OUR
C
OMPUTER
Figure 1: Top view
1
After removing your Ruckus Wireless AP from its pack-
age, place it next to your computer.
age, place it next to your computer.
2
Using an Ethernet cable, connect your computer’s net-
work port to one of the two ports on the AP.
work port to one of the two ports on the AP.
3
Using an AC adapter (sold separately), connect the AP
12VDC port to a protected power source.
12VDC port to a protected power source.
Alternatively, connect the PoE port to a PoE injector or
switch for both power and network connections.
switch for both power and network connections.
4
Verify that the Power LED on the external enclosure is a
steady green.
steady green.
Figure 2: Bottom view
S
TEP
3: P
REPARE
Y
OUR
C
OMPUTER
FOR
AP
S
ETUP
1
On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as fol-
lows:
adapter from the Local Area Connection settings as fol-
lows:
•
Start > Control Panel > Network and Sharing
Center > Change Adapter Settings
Center > Change Adapter Settings
2
Edit the TCP/IPv4 address settings as follows:
•
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
3
Select Use the following IP address (if it is not already
selected) and then make the following entries:
selected) and then make the following entries:
•
IP address: 192.168.0.22 (or any address in the
192.168.0.x network)
192.168.0.x network)
•
Subnet mask: 255.255.255.0
•
Default gateway: 192.168.0.1
Leave the DNS server fields empty.
4
Click OK to save your changes.
Your changes are put into effect immediately.
Note: The R600 requires a minimum of ZoneFlex (ZF)
firmware version 9.8.1 or later, or SmartCell Gateway
(SCG) firmware version 2.5.1 or later, or virtual SmartCell
Gateway (vSCG) 3.0 or later.
firmware version 9.8.1 or later, or SmartCell Gateway
(SCG) firmware version 2.5.1 or later, or virtual SmartCell
Gateway (vSCG) 3.0 or later.
IMPORTANT!
If the AP is deployed with a ZoneDirector, then
refer to the ZoneDirector Quick Setup Guide and connect the
AP to your local network.
AP to your local network.
Note: The following procedures assume Windows 7 as the
operating system. Procedures for other OS’s are similar.
operating system. Procedures for other OS’s are similar.
Important!
Write down all of the currently active settings so
you can restore your computer to its current configuration
later (when this process is complete).
later (when this process is complete).
PoE Port
12VDC Port