Ruckus Wireless R600 Benutzerhandbuch
Copyright © 2014 Ruckus Wireless, Inc.
Page 3 of 4
Published September 2014, Part Number 800-70633-001 Rev B
Mounting on a Recessed Drop-Ceiling T-Bar
The enclosed T-bar bracket supports mounting to recessed
drop ceiling T-bars.
drop ceiling T-bars.
•
•
•
Mounting an AP using the External Bracket
1
Insert the unit removal pin (A in
) into the hole on
the side of the R600 (B in
) to release the locking
mechanism.
Figure 4. Attaching the external bracket to the AP
2
Position the studs on the bottom of the T-bar bracket (C
in
in
) in the mounting holes on the R600 enclosure,
and then slide the T-bar bracket until the studs are in the
narrow parts of the R600 mounting keyholes (arrow).
narrow parts of the R600 mounting keyholes (arrow).
3
Remove the unit removal pin (A in
) to engage
the locking mechanism and secure the T-bar bracket to
the R600.
the R600.
4
Make sure that the locking tab (D in
first position on the T-bar bracket (C in
).
5
Gently push the ceiling tiles up and out of the way.
6
Position the T-bar bracket so its two clasps grip one edge
of the T-bar (A in
of the T-bar (A in
). Make sure that both clasps
are gripping the T-bar.
Figure 5. Attaching the external bracket to the T-bar
7
Hold the R600 in place and gently push the locking tab
(B in
(B in
) until its clasp grips the other edge of the T-
bar.
Removing an External Bracket from a T-Bar
1
Move the ceiling tiles out of the way.
2
Gently lift up the locking tab (A in
) by sliding
your fingers under the tab.
3
While lifting up on the locking tab, rotate the R600-
and-T-bar bracket assembly (B in
and-T-bar bracket assembly (B in
). The R600-
and-T-bar bracket assembly comes away from the T-
bar.
bar.
Figure 6. Removing the external bracket from the T-bar
Removing an External Bracket from an AP
1
Insert the unit removal pin (A in
) into the hole
on the side of the R600.
2
Gently lift up the retainer tab (B in
3
Gently push the T-bar bracket (C in
detaches from the R600.
Figure 7. Removing the external bracket from an AP
Mounting on a Flush Drop-Ceiling T-Bar
•
•
Mounting an AP using the Integrated Bracket
1
Orient the AP so that the T-bar is positioned between
the T-bar clips as shown in
the T-bar clips as shown in
, then rotate the AP
until the third T-bar clip catches the T-bar and the
latch locks the T-bar in place (
latch locks the T-bar in place (
).
Figure 8. Attaching the integrated bracket to the T-bar
Figure 9. Locking the integrated bracket to the T-bar
2
Insert the Torx security screw into the hole near the
latch to lock the AP in place.
latch to lock the AP in place.
Removing an AP Integrated Bracket from a T-Bar
1
To remove the AP from a T-bar, first remove the
security screw, then depress the latch while rotating
the AP so that the T-bar clips disengage the T-bar.
security screw, then depress the latch while rotating
the AP so that the T-bar clips disengage the T-bar.
Mounting on a Truss or Pole
1
Feed the customer-supplied cable ties through the
two slots on the back of the R600.
two slots on the back of the R600.
2
Fasten the R600 to the truss or pole using the cable
ties.
ties.
Note: This mounting bracket can also be used on a flush
drop-ceiling T-bar, so the four rubber feet on the bottom
of the AP minimize ceiling tile displacement.
drop-ceiling T-bar, so the four rubber feet on the bottom
of the AP minimize ceiling tile displacement.
A
B
C
D
A
B
CAUTION:
Make sure that all three clasps are gripping the T-
bar!
A
B
C
B
A