Hahntek Technology Corp M3688 Benutzerhandbuch
Introduction
This mouse set is a wireless input device with 27MHz radio
frequency. It is plug & play with Windows 98/SE/ME/2000/
XP/NT,without the need of any software installation.If you did
install any software for your previous keyboard or mouse,
please remove the mouse driver before use this new device.
Receiver Box
System Requirement :
Related PC compatibles USB
ports for mouse Microsoft Windows 98/SE/Me/2000/XP/NT
RF Mouse
Connect The Receiver :
The wireless mouse uses two AAA batterise.(For the best
performance, please use only alkaline batteries)
Install the Batteries :
RF Mouse
Remove Cover
Two AAA
batterise
Insert batterise
1.Turn off the computer before connecting the receiver to your
computer.
2.Working on metallic surface will reduce the RF performance.
Avoid placing the mouse on metallic surface.
3.Plug or unplug cable from the computer's USB ports improperly
can cause damage to the USB ports and to the computer.
4.Blinking alarm Red LED at scroll button when batteries failure.
5.For power saving designed. Press anyone of the Left or Right
button to start curso after few minutes being no use.
This wireless mouse set consists of mouse and receiver.
When you do not need to use the wireless mouse for a long
period of time, please remove the batteries and store them in
a dry place with normal room temperature.
Caution :
After intstall the batteries and connect the receiver to computer, turn on
your computer. If the product can not work or there are multi- products
be used. To avoid the interfrernce, you can do the follow procedures as
below to set the ID code. There is an ID button on the back side of the
Mouse and another one on the side of the Receiver.
1.Step1:press the ID set on Receiver, then press the ID button on
Mouse. The ID code will be set automatically.
You can first do any step, then another step. The process of each
step must be completed within 5 seconds.
2.After above process, the Receiver's RF LED will blink, when you move
the mouse. This means that the mouse do communicate with the
receiver successfully.
3.If not , the mouse can not work propperly.Please retry the above set
up process.
Set The ID Codes
RF Mouse
ID Set
1.Any move of batteries, or reconnect the Receiver, Please carry out the
above procedures to set the ID code again.Otherwise, the unit can not
work properly.
2.This product is a signal RF mouse. If two units are used within the
effective working range, radio interference will affect the performance
of your input, please re-set ID code again to a different one will
minimize the degree of radio interference.
Receiver Box
RF Signal LED
ID Set
After successful installation, the mouse can work well with Windows
98/SE/Me/2000/XP/NT, without the need of software driver.
Use The Mouse
The mouse comes with a scrolling wheel, which can function either as a
wheel or as a button.
1.To scroll up, move the wheel forward; to scroll down, move the wheel
backward.
2.To use the wheel like a standard mouse middle button, simply click
(press down) the wheel button.
1.If your mouse can not work after installation, please check follwings:
a).Make sure you have connected the receiver correctly to computer's
USB ports.
b).Make sure you have inserted the batterise correctly.
c).Make sure you have set the ID code properly, as stated above.
2.If your mouse isn't detected by the computer, please check followings:
a).Make sure the receiver is plugged onto the right USB port. Don't plug
and unplug the receiver's connectors, while the computer is on.
b).Make sure your USB ports have the proper configuration. Refer to
your computer documents for right configuration.
c).You may have other system device(s)(e.g.modem card)that is/are
conflicting your mouse. Check the IRQ address setting of these
devices, and change the setting as required. Refer to your computer
documents to make the changes.
3.If the mouse cursor does not move properly please check followings:
a).Check the large metal devices, such as microwave, electric stove,
television, hair dryer...., which may interfere the receiver's radio
reception.
b).Check the status of the batteries. The batteries maybe near dead.
If the mouse does not work after some time of usage, please replace
the batterise to see if it can solve the problem.
Trouble Shooting
WARNING:Take frequent breaks from typing to reduce
the risk of the wrists.
Caution :
Caution :
Channel SW
RF wireless mouse uses digital radio technology to communicate. It
transmits radio frequency signals which are picked by the receiver,
then passed to the computer.
The receiver is connected to the computer's USB ports via a cable.
Receiver to port, Voltage Rating DC 5V, Current Rating 15mA
Thank you for purchasing the Hahntek M3688 Optical
RF Wireless Mouse. Read this manual carefully before
using the controller and always keep it close at hand
while the controller is in use.
Installation Manual
M3688
Optical RF Wireless/Mouse set
Detailed read this manual through to acquire
PUSH BUTTON
RF Mouse
Receiver
PC
Keyboard
Monitor