Hahntek Technology Corp M3688 Manual Do Utilizador

This mouse set is a wireless input device with 27MHz radio 

frequency. It is plug & play with Windows 98/SE/ME/2000/ 

XP/NT,without the need of any software installation.If you did 

install any software for your previous keyboard or mouse,

please remove the mouse driver before use this new device.

Receiver Box

System Requirement : 

Related PC compatibles USB

ports for mouse Microsoft Windows 98/SE/Me/2000/XP/NT

RF Mouse

The wireless mouse uses two AAA batterise.(For the best 

performance, please use only alkaline batteries)

RF Mouse

Remove Cover

Two AAA 

batterise

Insert batterise

1.Turn off the computer before connecting the receiver to your

   computer.

2.Working on metallic surface will reduce the RF performance.

   Avoid placing the mouse on metallic surface.

3.Plug or unplug cable from the computer's USB ports improperly

   can cause damage to the USB ports and to the computer.

4.Blinking alarm Red LED at scroll button when batteries failure.

5.For power saving designed. Press anyone of the Left or Right 

   button to start curso after few minutes being no use.

When you do not need to use the wireless mouse for a long 

period of time, please remove the batteries and store them in 

a dry place with normal room temperature.

After intstall the batteries and connect the receiver to computer, turn on 

your computer. If the product can not work or there are multi- products 

be used. To avoid the interfrernce, you can do the follow procedures as 

below to set the ID code. There is an ID button on the back side of the 

Mouse and another one on the side of the Receiver.

1.Step1:press the ID set on Receiver, then press the ID button on 

   Mouse. The ID code will be set automatically.

   You can first do any step, then another step. The process of each 

   step must be completed within 5 seconds.

2.After above process, the Receiver's RF LED will blink, when you move

   the mouse. This means that the mouse do communicate with the 

   receiver successfully.

3.If not , the mouse can not work propperly.Please retry the above set 

  up process.

RF Mouse

ID Set

1.Any move of batteries, or reconnect the Receiver, Please carry out the

   above procedures to set the ID code again.Otherwise, the unit can not

   work properly.

2.This product is a signal RF mouse. If two units are used within the 

   effective working range, radio interference will affect the performance 

   of your input, please re-set ID code again to a different one will 

   minimize the degree of radio interference.

Receiver Box

RF Signal LED

ID Set

After successful installation, the mouse can work well with Windows 

98/SE/Me/2000/XP/NT, without the need of software driver.

The mouse comes with a scrolling wheel, which can function either as a 

wheel or as a button.

1.To scroll up, move the wheel forward; to scroll down, move the wheel 

   backward.

2.To use the wheel like a standard mouse middle button, simply click 

   (press down) the wheel button.

1.If your mouse can not work after installation, please check follwings:

 a).Make sure you have connected the receiver correctly to computer's

     USB ports.

 b).Make sure you have inserted the batterise correctly.

 c).Make sure you have set the ID code properly, as stated above.

2.If your mouse isn't detected by the computer, please check followings:

 a).Make sure the receiver is plugged onto the right USB port. Don't plug

     and unplug the receiver's connectors, while the computer is on.

 b).Make sure your USB ports have the proper configuration. Refer to 

     your computer documents for right configuration.

 c).You may have other system device(s)(e.g.modem card)that is/are 

     conflicting your mouse. Check the IRQ address setting of these 

     devices, and change the setting as required. Refer to your computer 

     documents to make the changes.

3.If the mouse cursor does not move properly please check followings:

 a).Check the large metal devices, such as microwave, electric stove, 

      television, hair dryer...., which may interfere the receiver's radio 

      reception.

 b).Check the status of the batteries. The batteries maybe near dead. 

      If the mouse does not work after some time of usage, please replace

      the batterise to see if it can solve the problem.

WARNING:Take frequent breaks from typing to reduce 

the risk of the wrists.

Channel SW

RF wireless mouse uses digital radio technology to communicate. It

transmits radio frequency signals which are picked by the receiver, 

then passed to the computer. 

The receiver is connected to the computer's USB ports via a cable.

Receiver to port, Voltage Rating DC 5V, Current Rating 15mA

Thank you for purchasing the Hahntek M3688 Optical 

RF Wireless Mouse. Read this manual carefully before 

using the controller and always keep it close at hand 

while the controller is in use.

Installation Manual

M3688

  Optical RF Wireless/Mouse set

PUSH BUTTON

RF Mouse

Receiver

PC

Keyboard

Monitor