Kenwo Industries Limited ARI60 Benutzerhandbuch
Ignition Disable / Anti-hijack Module (RID-5)
Installation
1. Cut the Ignition / Engine control wire (refer to options below)
2. Attempt to start bike to test if correct wire is selected. If bike starts the wrong wire is
selected. (contact Aritronix for assistance) If bike does not start, correct wire was
selected continue to step 3.
selected continue to step 3.
3. When Packaged the RID-5 wire ends have been treated with clear silicon to
protect the ends from fraying. Make sure they are stripped bare of this before
continuing.
continuing.
4. Connect one end of cut wire to one of the blue tap wires in RID-5 with provided
butt connector or any other solid connection options.
5. Connect second end of cut wire to second blue tab wire in RID-5 with provided
butt connector or any other solid connection options.
6. Test connections to insure that they are as solid as possible. *
7. Plug the RID-5 connector into the matching connector on Main Control Module
7. Plug the RID-5 connector into the matching connector on Main Control Module
(MCM) Accessory Harness.
8. Test RID-5 by activating alarm (without perimeter sensor) and try to turn on bike. If
bike turns on, please contact Aritronix for assistance.
* Failure to test for a loose wire could cause an accidental engine cut off.
The Ignition / Engine control wire Options:
Option #1: Positive lead wire on fuel pump
Option #2: Positive Lead wire on fuel injection system
Option #3: Positive Wire that goes to the ignition fuse in fuse box. This should be
either a 10 or 15 amp fuse labeled IGN or START. (Carbureted Bikes)
Option #4: Ground wire from ignition module
Option #5: Positive wire from ignition module to ignition coil.
Option #5: Positive wire from ignition module to ignition coil.
Option #6: Wire connected between the Ignition module and engine stop button.
Operating the Anti-Hijack feature
While the engine is running, press and hold the transceivers’ button #1 and button #2 at
the same time for 5 seconds. The siren will begin to chirp confirming that the Anti-Hijack
the same time for 5 seconds. The siren will begin to chirp confirming that the Anti-Hijack
feature has been activated. 15 seconds later, the siren will go off continuously, and the
engine will shut down. To disarm, turn off the ignition switch and press button #2.
engine will shut down. To disarm, turn off the ignition switch and press button #2.
13
Installation
Components List
MCM (Main Control Module)
Remote Transceiver
Accessory Harness
Generic Installation Kit (GEN-1)
Main Harness (HAR-1)
Planning the Installation
It is very important that before starting the installation of the security system, you
carefully read the installation instructions and spend time planning the installation. By
planning ahead you will be able to select the best approach in placing, securing and
planning ahead you will be able to select the best approach in placing, securing and
wiring the system to your specific motorcycle. Although the installation is not difficult,
there are a number of steps that must be taken for the system to operate properly. We
there are a number of steps that must be taken for the system to operate properly. We
suggest the following steps:
1. Check that your motorcycle battery is fully charged and that all electrical circuits
are in good working condition.
2. Check the layout and construction of the motorcycle to decide what space is
available to place the components.
3. Verify that no moving parts interfere with the components or their wires.
4. Do not route wires near sharp edges, which could cut wires and cause a short.
5. Do not mount components near extreme heat areas such as exhaust pipes etc.
6. Allow at least an inch or two of slack at all connection points to reduce the chance
4. Do not route wires near sharp edges, which could cut wires and cause a short.
5. Do not mount components near extreme heat areas such as exhaust pipes etc.
6. Allow at least an inch or two of slack at all connection points to reduce the chance
that a connection will break apart due to vibration.
7. Select a suitable location underneath the seat or in a side cover. Mount the MCM
using Velcro or cable ties. Make sure that it is not exposed or easily reached.
2
To CUT wire on Motorcycle
To Accessory Harness on
Main Control Module (MCM)
Main Control Module (MCM)