Adtran TRC4208 Benutzerhandbuch
Section 5 User Interface Guide
TRACER 4208 System Manual
48
© 2003 ADTRAN, Inc.
612804208L1-1A
>TRACER S
YSTEM
C
ONFIGURATION
> S
ITE
N
AME
Provides a user-defined alphanumeric discription (up to 25 characters) for the TRACER 4208 system.
>TRACER S
YSTEM
C
ONFIGURATION
> RF B
ANDPLAN
Sets the bandplan for the TRACER 4208. Each channel is divided into three bandplans (1, 2, or 3). Both
local and remote TRACER 4208 must be configured with the same bandplan (1, 2, or 3) but different
channel plans (Plan A or Plan B). For example, the transmitter at one end of the link will transmit in
bandplan 1 of channel A (the lower portion of the spectrum) and receive in bandplan 1 of channel B (the
upper portion). Consequently, the receiver at the other end should receive in bandplan 1 of channel A (the
lower portion) and transmit in bandplan 1 of channel B (the upper portion). (Refer to Figure 5). The
TRACER 4208 comes factory programmed with RF bandplan set to Band 1.
local and remote TRACER 4208 must be configured with the same bandplan (1, 2, or 3) but different
channel plans (Plan A or Plan B). For example, the transmitter at one end of the link will transmit in
bandplan 1 of channel A (the lower portion of the spectrum) and receive in bandplan 1 of channel B (the
upper portion). Consequently, the receiver at the other end should receive in bandplan 1 of channel A (the
lower portion) and transmit in bandplan 1 of channel B (the upper portion). (Refer to Figure 5). The
TRACER 4208 comes factory programmed with RF bandplan set to Band 1.
Figure 5. 5.8 GHz Bandwidth Division (TRACER 4208)
>TRACER S
YSTEM
C
ONFIGURATION
> M
ODEM
C
ONTROL
Configures the modem control leads on the RS-232 port (terminal interface located on the rear panel of the
unit). Set
unit). Set
M
ODEM
C
ONTROL
to
E
NABLED
when connecting the unit to a modem (using a null modem
adapter). Setting
M
ODEM
C
ONTROL
to
D
ISABLED
prevents the TRACER 4208 from monitoring DCD and
enables data to be sent to the VT100 continuously.
M
ODEM
C
ONTROL
must be set to
D
ISABLED
when the
VT100 terminal is in use. The TRACER 4208 comes factory programmed with
M
ODEM
C
ONTROL
set to
D
ISABLED
.
>TRACER S
YSTEM
C
ONFIGURATION
> M
ODEM
C
ONNECTION
(L
OGOUT
)
Causes the TRACER 4208 to de-assert Clear To Send (CTS) and DSR for a time greater than 20 msec.
This signals the modem to disconnect the analog connection. Hangup-On-DTR-Drop may need to be
explicitly enabled on some modems. If
This signals the modem to disconnect the analog connection. Hangup-On-DTR-Drop may need to be
explicitly enabled on some modems. If
P
ASSWORD
P
ROTECTION
is
E
NABLED
, this menu also causes the unit
to close the current session and return to the TRACER System Status menu page and wait for password
input.
input.
Press <Ctrl+Z> three times from the terminal interface to disable
M
ODEM
C
ONTROL
when
the modem control leads are active.
Channel A
5742
725
5787
5850
5747
5753
MHz
M
Bandplan 3
Bandplan 2
Bandplan 1
Channel B
5815
5827
5833
Bandplan 3
Bandplan 2
Bandplan 1