Xmark Corporation ITG Benutzerhandbuch
100-13551 Commerce Parkway
Richmond, BC Canada V6V 2L1
Toll Free (800) 667-9689
Phone (604) 207-7760
Fax (604) 207-7765
E-mail: info@exi.com
www.exi.com
Richmond, BC Canada V6V 2L1
Toll Free (800) 667-9689
Phone (604) 207-7760
Fax (604) 207-7765
E-mail: info@exi.com
www.exi.com
© September 2004, eXI Wireless Inc. Specifications subject to change without notice.
980-000037-000R1.00
980-000037-000R1.00
Infant Tag User Guide
INFANT TAG OVERVIEW
Infant Tag
AR4TA02-00P
Infant Tag w/ Tag Pulse
AR4TA01-00P
As an essential part of the HALO Infant
Protection System™, the Infant Tag helps to
protect and identify infants in your care.
Each tag is labeled with a unique serial
number and expiry date for easy, accurate
identification.
Protection System™, the Infant Tag helps to
protect and identify infants in your care.
Each tag is labeled with a unique serial
number and expiry date for easy, accurate
identification.
The bottom of the tag is curved to ensure a
snug and comfortable fit.
snug and comfortable fit.
Tag pulse technology allows tags to emit
periodic signals to the HALO system that
allow facilities to accurately track and locate
infants. Infant Tags are available with and
without tag pulse technology.
periodic signals to the HALO system that
allow facilities to accurately track and locate
infants. Infant Tags are available with and
without tag pulse technology.
APPLICATION
Proper banding will limit the incidence of
nuisance alarms. A properly fastened strap
should keep the bottom of the Infant Tag
against the infant’s skin, but it should
neither restrict the infant’s circulation nor
cause discomfort or chafing.
nuisance alarms. A properly fastened strap
should keep the bottom of the Infant Tag
against the infant’s skin, but it should
neither restrict the infant’s circulation nor
cause discomfort or chafing.
eXI recommends using either the Velcro
Strap or the Stockinette to attach the Infant
Tag. However, other options are available.
For more information, contact your dealer
or eXI directly.
Strap or the Stockinette to attach the Infant
Tag. However, other options are available.
For more information, contact your dealer
or eXI directly.
STEP 1: APPLY SECURE STRIP*
Secure Strip
AR3SS01-000
(Roll of 1000 pre-cut adhesives)
•
Hold Infant Tag with top
uppermost
uppermost
•
Remove Secure Strip from
tape by slightly bending
tape, allowing strip to separate
tape by slightly bending
tape, allowing strip to separate
•
Center strip on bottom of tag and
press firmly into place
press firmly into place
•
Follow instructions for type of strap used
STEP 2: BANDING
Velcro Strap
AR3WS01-VLC
(Pack of 10)
•
Insert velcro tab end of strap through one
arm of tag. Guide it from top to bottom of
tag, with tan color next to the infant’s skin
arm of tag. Guide it from top to bottom of
tag, with tan color next to the infant’s skin
•
Pull taut
•
Peel backing from Secure Strip
•
Place tag on infant’s calf or upper arm
•
Guide tab end
through tag’s
other arm
through tag’s
other arm
•
Fold tab back
over arm to
adhere velcro to
strap
over arm to
adhere velcro to
strap
Stockinette (S - 1.25”)
AR3WS01-SML
Stockinette (M - 1.625”)
AR3WS01-MED
Stockinette (L - 2”)
AR2WSD1-SOC
(Bag of 50)
•
Peel backing from Secure Strip
•
Place tag on infant’s calf or
upper arm
upper arm
•
Center stockinette
over tag
over tag
Coban (3M product available from medical
supply companies)
supply companies)
•
Peel backing from Secure Strip
•
Place tag on infant’s calf or upper arm
•
Wrap Coban around tag,
covering the tag
completely; ensure that
you do not wrap the Coban
too tightly
completely; ensure that
you do not wrap the Coban
too tightly
CLEANING
TAGS
In order to disinfect without causing
damage to the tags, use one of the
following cleaning methods:
damage to the tags, use one of the
following cleaning methods:
METHOD 1
•
Scrub each tag with germicidal solution of
approximately 60 seconds
Note: Phenolic or iodine base solution is
preferred
approximately 60 seconds
Note: Phenolic or iodine base solution is
preferred
•
Wipe each tag individually (using a new
alcohol wipe for each)
•
Allow tag to dry for 30 seconds
METHOD 2
•
Use cold sterilization in Cidex or Totacide
Note: Do not immerse tags for more than 30
minutes
Note: Do not immerse tags for more than 30
minutes
METHOD 3
•
Use gas diffusion sterilization methods
Note: Battery leakage may occur if tags are
exposed to heat in excess of 57°C (135°F)
Note: Battery leakage may occur if tags are
exposed to heat in excess of 57°C (135°F)
Important: Tags are incompatible with
disinfectants containing Glycol Ether.
disinfectants containing Glycol Ether.
STRAPS
The Velcro Strap and the Stockinette are
disposable and intended for single use,
which eliminates the need for sterilization
and disinfection. If need be, the Velcro Strap
will withstand hand washing.
disposable and intended for single use,
which eliminates the need for sterilization
and disinfection. If need be, the Velcro Strap
will withstand hand washing.
STORAGE
Tag Rack
AGETR02-000
Store tags in eXI’s Tag Rack at room
temperature. The
Tag Rack holds up
to 42 curved
Infant Tags.
temperature. The
Tag Rack holds up
to 42 curved
Infant Tags.
Regularly rotate
your tag inventory
so that tags are used evenly.
your tag inventory
so that tags are used evenly.
ORDER INFORMATION
To re-order tags, secure strips, or bands,
contact your dealer or eXI directly. Use the
order numbers in bold and italics to ensure
you get exactly what you need.
contact your dealer or eXI directly. Use the
order numbers in bold and italics to ensure
you get exactly what you need.
*Optional
Top
Arm
Arm
Curved Bottom -
Sensing Surface
Sensing Surface
eXI Wireless Systems
Model No.: Infant Tag
IC: 2877A-ITG
FCC ID: HE7ITG
* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two rules: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Any
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Made in Canada