Digital Monitoring Products Inc 793 Benutzerhandbuch
LT
-0740 (11/03) © 2003 Digital Monitoring P
roducts, Inc.
800-641-4282
www.dmp.com
Made in the USA
INTRUSION • FIRE • ACCESS • NETWORKS
2500 North Partnership Boulevard
Springfield, Missouri 65803-8877
SpeciÞ cations
Operating Voltage
8 - 14.5 VDC
Dimensions
6.5” W x 5” H x 1” D
Panel Compatibility
DMP Command Processor™ Panels
XRSuper6, XR20, XR40
XR200, XR200-485, XR2400F
XR500, XR500N
XRSuper6, XR20, XR40
XR200, XR200-485, XR2400F
XR500, XR500N
Approvals
• Underwriters Laboratories
• New York Material Equipment Acceptance (MEA)
• California State Fire Marshal (CSFM)
• Factory Mutual (FM)
• New York Material Equipment Acceptance (MEA)
• California State Fire Marshal (CSFM)
• Factory Mutual (FM)
Compatible Access Devices
The 693, 791, and 793 Keypads are compatible with the following readers.
Readers
Standby Current
Peak Current
PP-6005B ProxPoint Plus
30mA
75mA
MP-5365 MiniProx
20mA
110mA
PR-5455 ProxPro II
25mA
125mA
MX-5375 Maxi-Prox
200mA
700mA
TL-5395 ThinLine II
20mA
115mA
Current Draw
Keypad
Voltage
Normal Standby
Alarm
693
791
8 VDC
46mA + 1.6mA per active zone
56mA + 2mA per active zone
14.5 VDC
77mA + 1.6mA per active zone
84mA + 2mA per active zone
793
8 VDC
62mA + 1.6mA per active zone
88mA + 2mA per active zone
14.5 VDC
92mA + 1.6mA per active zone
120mA + 2mA per active zone
FCC Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modiÞ cations made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modiÞ cations made by the user and not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.