Digital Monitoring Products Inc PC0086 Benutzerhandbuch

The 7000 Series keypads also contain Keypad Option and Keypad Diagnostic programs that allow installers and 

service technicians to configure and test keypad operation.
Access the User Menu
Access the Installer Options Menu through the User Options function.  Hold down the <— and CMD keys for a few 

seconds to display the SET BRIGHTNESS prompt.  Immediately enter the code 3577 (INST) and press CMD.  The 

display changes to KPD OPT (keypad options) KPD DIAG (keypad diagnostics) and STOP.
The keypad options menu allows you to set the keypad address, select supervised or unsupervised mode, change 

the default keypad message, individually arm the 2-button Panic keys, and select Soft-Shunt, Request-to-Exit, and 

4-digit entry cards. 
Programming Keypad Options

KPD  KPD

OPT  DIAG 

  STOP

To program keypad options, press the left Select key under KPD OPT.  The display 

changes to CURRENT KEYPAD ADDRESS:  # #. 

CURRENT KEYPAD

ADDRESS:    01

Set the keypad address from 01 to 05 with the XRSuper6 and XR20, from 01 to 08 

with the XR40, XR200, XR2400F, and 01 to 16 with the XR200-485, XR500 Series, and 

XR2500F.  The factory default address is set at 01.  To change the current address, press 

any Select key and then enter the new address using the appropriate number keys on 

the keyboard.  It is not necessary to enter a leading zero for addresses 01 to 09.

KEYPAD MODE:

*SUP 

 

 UNSUP

Configure the keypad for either supervised or unsupervised operation.  You have the 

option to supervise keypads with zones connected to them.  Supervised keypads cannot 

share addresses with other keypads.  To enhance the supervision feature, assign an 

output to the Device Fail Output in panel programming and connect a device to the 

corresponding output that trips when the keypad fails.  This provides notification at the 

central station and the site.  The other keypads do not display the device fail. 
Unsupervised keypads can operate with other unsupervised keypads sharing the same 

address.  Zones cannot be used on unsupervised keypads.  To change the current 

setting, press the Select key under SUP or UNSUP.  An asterisk appears next to the 

selected option.
Note: An unsupervised address cannot be programmed for Device Fail Output. 

DEFAULT KEYPAD MSG:   Default Keypad Message

Enter a custom message of up to 16 characters to appear on the keypad display top line 

whenever that line is not used for any other purpose.  Press any Select key to clear the 

current display and use the data entry keys to enter a new custom display. 

ARM PANIC KEYS:

*PN  *EM  *F1

Use this option to configure the top row Select keys as 2-button Panic keys.  To enable 

or disable a Panic, press the Select key under the appropriate display: PN (Panic), EM 

(Emergency), and FI (Fire).  Once the panic is enabled, an asterisk displays next to the 

description.  Refer to the Panic Key Options section earlier in this document.

7/0 PANIC 

ENABLE:    NO  YES

Use this option to configure the 7 and 0 keys as a 2-button Panic feature.  To enable 

the 7/0 Panic, select YES.  To disable the option, select NO.  Default is NO.  In a panic 

situation simply press and hold the 7 and 0 keys for two seconds.  Refer to the Panic 

Key Options section earlier in this document.

ACTIVATE ZONE 2

SHUNT: 

  NO  YES

Select YES to enable the Soft-Shunt™ option on zone 2. This zone provides the 

Soft-Shunt™ for door contacts. Zone 2 must be programmed into the panel.