Computime Limited RC713A Benutzerhandbuch
SPECIFICATIONS AND OTHER INFORMATION
INSTALLATION
USEFUL INFORMATION
1. Radio Receivers are sensitive to heat. Avoid
mounting them above heater, air conditioner
or exposed to afternoon sun.
or exposed to afternoon sun.
2. The higher the Receiver Module, the longer its
range. For good range and reliable reception, install
modules as high as practical above ground level with
antenna at top.
modules as high as practical above ground level with
antenna at top.
3. Large metal objects divert radio signals. Avoid
mounting Receiver Modules on metal wall, fence
or near large metal objects.
or near large metal objects.
4. Environmental conditions could effect the operation
of the remote control system. For example, in rain
the range may be less than normal.
the range may be less than normal.
5. Certain electric equipment like brush type motors
or electronic gas heater igniters emit radio signals
and can effect the function of the Receiver Module.
Avoid mounting modules near such equipment.
and can effect the function of the Receiver Module.
Avoid mounting modules near such equipment.
6. Antenna orientation may increase or decrease the
radio range. For best results, keep the antenna
straight and adjust for better radio reception by
bending the antenna near its base.
straight and adjust for better radio reception by
bending the antenna near its base.
A. ON/OFF Switching Application
- use Model RC713L
Make sure the intended load is within the capacity of the
Module, see ratings on page 1 and other choices on page 4.
Module, see ratings on page 1 and other choices on page 4.
1. Attach RC713L Receiver Module to the top of an outdoor grade
junction box. Make sure the assembly is raintight.
2. Select the proper location (see Useful Information above) and
install Receiver assembly on a vertical surface or other support,
using hardware, suitable for the purpose.
using hardware, suitable for the purpose.
3. Prepare the necessary conduit runs as required by the installation
layout and pull-in the specified conductors.
4. Follow wiring diagram A on the right, make wire connections
as shown.
5. Turn ON power and test installation, using the ON/OFF button
on face of the Receiver Module. Replace junction box cover,
make sure the installation is secure and raintight.
make sure the installation is secure and raintight.
6. Set code, see Operating Instructions on page 3.
2
OPERATION
B. Timer Override Application
- use Model RC715L
An existing timer can only be upgraded if the
load connected to the timer is within the
capacity of the Receiver Module. Otherwise,
the timer mechanism must be replaced with
Intermatic Model P1103ME, see also other
choices
on page 4.
load connected to the timer is within the
capacity of the Receiver Module. Otherwise,
the timer mechanism must be replaced with
Intermatic Model P1103ME, see also other
choices
on page 4.
1. Select the proper location (see Useful
Information on page 2) and install a radio
compatible timer on a vertical surface or
other support, using hardware, suitable for
the purpose.
compatible timer on a vertical surface or
other support, using hardware, suitable for
the purpose.
2. Prepare the necessary conduit runs as required
by the installation layout and pull-in the
specified conductors.
specified conductors.
3. Use one of the side knock-outs and a suitable
conduit-L, attach Model RC715L Receiver
Module to timer enclosure.
Module to timer enclosure.
4. Follow wiring diagram B on the right,
make wire connections as shown.
5. Turn ON power, and test installation,
using the ON/OFF control of the timer.
A. To Set Code
Receiver Modules have the capacity to “learn” and remember a unique code, generated by a Transmitter.
The Transmitter will operate only the designated Receiver. In addition, each Transmitter can “teach” and
operate up to four different of Receivers.
The Transmitter will operate only the designated Receiver. In addition, each Transmitter can “teach” and
operate up to four different of Receivers.
1. Turn ON the main power and manually operate the load a few times, then turn load OFF.
2. Press the “Code Set” button on the face of the Receiver Module. The green light next to the button should now be
lit and stay lit for 30 seconds.
3. Hold the Transmitter close to the Receiver Module, press and hold the push button on the Transmitter that you
choose to operate that particular Module. the red light on the Transmitter will light to indicate that it is
transmitting. On the Receiver Module, the green light will flash rapidly after it is programmed.
transmitting. On the Receiver Module, the green light will flash rapidly after it is programmed.
To operate more than one Receiver Module with the same Transmitter button, in step 2 press the :”Code Set” button
for each Receiver Module to be controlled. The green light next to the button will turn on. Press and hold the desired
transmitter button until all Receiver Module green lights begin to flash.
To operate Receiver Modules independently, program the Modules as shown in steps 2 and 3 but use a different
transmitter button for each Module.
for each Receiver Module to be controlled. The green light next to the button will turn on. Press and hold the desired
transmitter button until all Receiver Module green lights begin to flash.
To operate Receiver Modules independently, program the Modules as shown in steps 2 and 3 but use a different
transmitter button for each Module.
3
In case this device is used to operate pool/spa equipment...
DANGER! To Reduce the Risk of Injury:
... do not permit children to operate the Control Unit or use the Pool/Spa unless they are closely supervised at all times.
... test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualified service technician.
... test GROUND FAULT protection regularly. If it fails to reset, DO NOT USE THE POOL or SPA! Contact a qualified service technician.
Manual ON/OFF
Button (Model
RC713L Only)
Button (Model
RC713L Only)
Override Connections
(Model RC715L Only)
(Model RC715L Only)
7. To prevent electronic interference, install Receiver
Modules as far apart as practical.
Figure 1
*Ground connections may or may not be as shown.
Diagram A
*
Ground connections may or may not be as shown.
Diagram B
*
RC713L
Receiver
Module
RC715L
Receiver
Module