Nokia of America Corporation BBTRX-06 Benutzerhandbuch
• Electrical conduit installation equipment and materials
• Electrical tape
• ESD wrist strap (not provided with RRHs)
• Eye protection gear
• Fish tape
• Flashlight
• Floor punch, for cutting asbestos floor tile prior to drilling
• Floor tile puller, for raised floor tiles
• A hoist capable of lifting and moving the RRH into final position
• Galvanizing paint
• Gin boom
• Gloves - Low voltage rubber lineman's gloves (R-4285)
• Hammer, 16 oz. (.5 kg) for anchor installation
• Heat gun for heat shrink
• Insulated gloves
• Insulated hand tools (for completing electrical connections)
• Ladder or work stand/stool .
• Level (4 ft. - 1.5 m) (steel)
• Marker, to mark floor for lineup and drilling
• Measuring tape
• Nut driver set (decimal) with 10-inch extension
• Nut driver set (metric) with 250-mm extension
• Ohmmeter (Multimeter, volt/ohmmeter, or equivalent)
• Pallet jack
• Pliers
• Plumb line
• Pry bar
• Safety goggles or glasses (R-3055)
• Screwdrivers (power and manual), flat-blade, Phillips
• Silicone caulk
• Socket sets (decimal and metric) various drives, including 1/4" drive for security bit
• Stripping tool (for LDF4 antenna jumper cables) - part number 74Z-0-12-15 for
• Electrical tape
• ESD wrist strap (not provided with RRHs)
• Eye protection gear
• Fish tape
• Flashlight
• Floor punch, for cutting asbestos floor tile prior to drilling
• Floor tile puller, for raised floor tiles
• A hoist capable of lifting and moving the RRH into final position
• Galvanizing paint
• Gin boom
• Gloves - Low voltage rubber lineman's gloves (R-4285)
• Hammer, 16 oz. (.5 kg) for anchor installation
• Heat gun for heat shrink
• Insulated gloves
• Insulated hand tools (for completing electrical connections)
• Ladder or work stand/stool .
• Level (4 ft. - 1.5 m) (steel)
• Marker, to mark floor for lineup and drilling
• Measuring tape
• Nut driver set (decimal) with 10-inch extension
• Nut driver set (metric) with 250-mm extension
• Ohmmeter (Multimeter, volt/ohmmeter, or equivalent)
• Pallet jack
• Pliers
• Plumb line
• Pry bar
• Safety goggles or glasses (R-3055)
• Screwdrivers (power and manual), flat-blade, Phillips
• Silicone caulk
• Socket sets (decimal and metric) various drives, including 1/4" drive for security bit
• Stripping tool (for LDF4 antenna jumper cables) - part number 74Z-0-12-15 for
Huber Suhner connectors; part number ITE-7189 for Andrew connectors.
• Tools for preparing cables
• Torque wrenches, 35 - 300 in.-lb. (4 - 34 Nm)
• Torque wrenches, 4.4 -150 ft.-lb. (6 - 200 Nm)
• Torque wrenches, 35 - 300 in.-lb. (4 - 34 Nm)
• Torque wrenches, 4.4 -150 ft.-lb. (6 - 200 Nm)
Tools, materials, and checklist
Preparatory information
Preparatory information
Tools required for installation
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
4-4
Alcatel-Lucent – Proprietary
Use pursuant to applicable agreements
FDD RRH 700L
3MN-00075-0002-RJZZA
Issue 0
September 2012