E F Johnson Company 2425M70 Benutzerhandbuch
7-17
SMARTNET / SmartZone / P25 Trunked Features
7.11.1 Priority Talkgroup Sampling
One talkgroup in the scan list can be designated a priority talkgroup by programming or it
can be the selected talkgroup. When scanning, messages on a non-priority talkgroup are
interrupted by messages on the priority talkgroup. Priority scanning must also be
supported at the system level for it to occur as programmed in the radio. P25 Trunking
supports dual priority scan, therefore two priority talkgroups can be selected.
can be the selected talkgroup. When scanning, messages on a non-priority talkgroup are
interrupted by messages on the priority talkgroup. Priority scanning must also be
supported at the system level for it to occur as programmed in the radio. P25 Trunking
supports dual priority scan, therefore two priority talkgroups can be selected.
The Control Channel handles all traffic for the radios and communicates which talkgroups
are using which channels. If the radio “receives” the ID for one of its talkgroups, it can go
to that voice channel and hear the talkgroup. When the radio is ON the voice channel, it
cannot receive information about which talkgroups are on which channel. The radio will
not know about any new talkgroup activity till it finishes the voice channel and returns to
the Control Channel.
are using which channels. If the radio “receives” the ID for one of its talkgroups, it can go
to that voice channel and hear the talkgroup. When the radio is ON the voice channel, it
cannot receive information about which talkgroups are on which channel. The radio will
not know about any new talkgroup activity till it finishes the voice channel and returns to
the Control Channel.
If a Talkgroup is set as a Priority Monitor talkgroup on the system, the system sends the
Talkgroup’s call information over the voice channel so it can be detected and move to this
priority call. So even if the radio cannot hear the Control Channel, it will receive the call
information and switch to the channel with the priority call.
Talkgroup’s call information over the voice channel so it can be detected and move to this
priority call. So even if the radio cannot hear the Control Channel, it will receive the call
information and switch to the channel with the priority call.
Note
The Priority Monitor must not be confused with Transmit Priority, which is used when a
call is placed in Queue when all the Voice Channels are busy.
call is placed in Queue when all the Voice Channels are busy.
7.11.2 Scan List Editing and Selection
SMARTNET/SmartZone and P25 Trunked scan lists are user programmable if the SCN
ED option switch is programmed (or if the menu parameter is selected). The procedure is
described in Section 5.13.1.
ED option switch is programmed (or if the menu parameter is selected). The procedure is
described in Section 5.13.1.
With SMARTNET/SmartZone and P25 trunked operation, each channel (talkgroup) can
be programmed to select one of the programmed scan lists or so scanning is disabled (No
List). In addition, each channel can be programmed so that scanning is automatically
enabled (Auto Scan) when it is selected. P25 Trunking supports dual priority scan,
therefore two priority talkgroups can be selected.
be programmed to select one of the programmed scan lists or so scanning is disabled (No
List). In addition, each channel can be programmed so that scanning is automatically
enabled (Auto Scan) when it is selected. P25 Trunking supports dual priority scan,
therefore two priority talkgroups can be selected.
If the SN LIST option switch is programmed (or if the menu parameter is selected), the list
that is selected by all talkgroups in the current system can be temporarily changed by the
user as follows. Also selectable if desired is “Programmed” (default list). The temporary
programmed scan list is retained through radio power downs.
that is selected by all talkgroups in the current system can be temporarily changed by the
user as follows. Also selectable if desired is “Programmed” (default list). The temporary
programmed scan list is retained through radio power downs.
Proceed as follows to temporarily change the currently selected scan list:
1 With scanning disabled (the rotating icon is not indicated in the right status display),
press the SN LIST option switch.
2 The currently selected list is displayed as “LIST x”, with “x” the currently selected list.
To exit without changing the selected list, press the SN LIST option switch again.
Draft 4/29/2014