Vital Home Systems LLC 1060 Benutzerhandbuch
P a g e
| 5
© 2015 - 2016 Vital Home Systems, LLC
The Wireless Control Panel LED will also flash
ON, enabling the person testing the range from
afar to see the condition in case the beep
cannot be heard.
ON, enabling the person testing the range from
afar to see the condition in case the beep
cannot be heard.
NOTE:
Once a sensor has been successfully
Learned-In, the Wireless Control Panel LED
will stay lit for another 60 seconds to allow
you to Learn-In the next one.
will stay lit for another 60 seconds to allow
you to Learn-In the next one.
Once in Range-Test Mode, if a key is not
pressed for 30 minutes, the Wireless
Control Panel will sound five (5) quick-
beeps then automatically exit Range-Test
Mode and return to Program Mode.
Control Panel will sound five (5) quick-
beeps then automatically exit Range-Test
Mode and return to Program Mode.
You may exit Range-Test Mode to return to
Programming Mode anytime by pressing
“CLR” key.
“CLR” key.
To exit Programming Mode and return to
Normal Mode, press “CLR” key.
To enter Range-Test Mode, return to
Step 1.
Exit Programming Mode
Press “CLR” key to exit the Programming Mode and
return to Normal Mode.
return to Normal Mode.
Reset Wireless Control Panel to Default
Settings
Settings
Step 1: Remove all power sources, including AC
power adaptor and battery. (To remove the
battery remove the 4 black feet and unscrew
the 4 case screws. Be careful not to over
tighten the screws when putting back together
so as not to strip the screw holes. Unplug the
battery from the PC board).
battery remove the 4 black feet and unscrew
the 4 case screws. Be careful not to over
tighten the screws when putting back together
so as not to strip the screw holes. Unplug the
battery from the PC board).
Step 2: With the panel apart keeping the “CLR” key
pressed, plug in the AC power adaptor. A long
one-second beep will emit indicating that the
Panel has been successfully reset to Default
Settings.
one-second beep will emit indicating that the
Panel has been successfully reset to Default
Settings.
Step 3: Plug the battery back in and close the case
carefully not to over tighten the screws.
NOTE:
Under Factory Default Setting –
Under Factory Default Setting –
PIN code is set as “0000”
Wireless Control Panel is cleared of all
telephone numbers.
telephone numbers.
Wireless Control Panel is cleared of all
sensor devices.
sensor devices.
Operation
IMPORTANT NOTICE TO USER: The installation of
any water detection or automatic water shut off
system does NOT guarantee water will be detected
on all occasions or circumstances. Due to the
variety of environments the system can be
installed, how it is maintained and types of
installation, Vital Home Systems does NOT
guarantee or warrant against water or property
damage as a result of or/with the use of this
system.
any water detection or automatic water shut off
system does NOT guarantee water will be detected
on all occasions or circumstances. Due to the
variety of environments the system can be
installed, how it is maintained and types of
installation, Vital Home Systems does NOT
guarantee or warrant against water or property
damage as a result of or/with the use of this
system.
Upon receiving the signal from the Water Sensors or
VC100, the Wireless Control Panel will flash the
Wireless Control Panel POWER LED and play the
appropriate message for specific event and time
period.
VC100, the Wireless Control Panel will flash the
Wireless Control Panel POWER LED and play the
appropriate message for specific event and time
period.
NOTE:
For VC-100 / AWS/TWS, it will play
appropriate voice message locally for 15
seconds before dialing out.
seconds before dialing out.
If two or more sensors are triggered one
after another, the corresponding messages
will be played in rotation.
will be played in rotation.
After the Audio is played the SMS messages
will begin to be sent from the Wireless
Control Panel
Control Panel
If no telephone number is stored, the
Wireless Control Panel will not send SMS
reports
reports
When two or more telephone numbers are
stored, the Wireless Control Panel will send
SMS reports in accordance to the Priority
Order number.
SMS reports in accordance to the Priority
Order number.
If prior to or during voice alarm playback,
the Wireless Control Panel receives a
disarm signal via SMS or when its “ACK” key
is pressed, the Wireless Control Panel
Power LED stops blinking and the Wireless
Control Panel stops the reporting.
disarm signal via SMS or when its “ACK” key
is pressed, the Wireless Control Panel
Power LED stops blinking and the Wireless
Control Panel stops the reporting.
The Wireless Control Panel phone numbers
entered are to be for cell phone numbers
only for SMS receipt
only for SMS receipt
Fault Situations
The Yellow LED (Fault LED) will flash ON if the VHS-
Wireless Control Panel or any of the Learned
devices have a fault such as are disconnected or in a
continual low-battery status.
Wireless Control Panel or any of the Learned
devices have a fault such as are disconnected or in a
continual low-battery status.
The Yellow LED will turn OFF automatically
once all of the faulty conditions are
restored, or faulty devices are removed via
the software.
restored, or faulty devices are removed via
the software.